- 您現在的位置：買賣IC網 > PDF目錄383182 > ISL9440A (Intersil Corporation) Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller PDF資料下載
參數資料
| 型號： | ISL9440A |
| 廠商： | Intersil Corporation |
| 英文描述： | Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller |
| 中文描述： | 三，180Σ門診的階段，降壓型PWM和線性控制器單 |
| 文件頁數： | 15/20頁 |
| 文件大小： | 978K |
| 代理商： | ISL9440A |
15
FN6383.1
December 5, 2007
Where Q
GATE
is the amount of gate charge required to fully
charge the gate of the upper MOSFET. The
Δ
V
BOOT
term is
defined as the allowable droop in the rail of the upper drive.
As an example, suppose an upper MOSFET has a gate
charge (QGATE) of 25nC at 5V and also assume the droop
in the drive voltage over a PWM cycle is 200mV. One will
find that a bootstrap capacitance of at least 0.125μF is
required. The next larger standard value capacitance is
0.22μF. A good quality ceramic capacitor is recommended.
Protection Circuits
The converter output is monitored and protected against
overload, short circuit and undervoltage conditions. A
sustained overload on the output sets the PGOOD low and
initiates hiccup mode.
Undervoltage Lockout
The ISL9440, ISL9440A and ISL9441 include UVLO
protection that will keep the devices in a reset condition until
a proper operating voltage is applied and that will also shut
down the ISL9440, ISL9440A and ISL9441 if the operating
voltage drops below a pre-defined value. All controllers are
disabled when UVLO is asserted. When UVLO is asserted,
PGOOD will be valid and de-asserted.
Overcurrent Protection
All the PWM controllers use the lower MOSFET’s
on-resistance, r
DS(ON)
, to monitor the current in the
converter. The sensed voltage drop is compared with a
threshold set by a resistor connected from the OCSETx pin
to ground.
where, I
OC
is the desired overcurrent protection threshold,
and R
CS
is a value of the current sense resistor connected to
the ISENx pin. If an overcurrent is detected for 2 consecutive
clock cycles then the IC enters a hiccup mode by turning off
the gate drivers and entering into soft-start. The IC will cycle
4 times through soft-start before trying to restart. The IC will
continue to cycle through soft-start until the overcurrent
condition is removed. Hiccup mode is active during soft-start
so care must be taken to ensure that the peak inductor
current does not exceed the overcurrent threshold during
soft-start.
Because of the nature of this current sensing technique, and
to accommodate a wide range of r
DS(ON)
variations, the
value of the overcurrent threshold should represent an
overload current about 150% to 180% of the maximum
operating current. If more accurate current protection is
desired, place a current sense resistor in series with the
lower MOSFET source.
Overvoltage Protection
All switching controllers within the ISL9440, ISL9440A and
ISL9441 have fixed overvoltage set points. The overvoltage
set point is set at 118% of the output voltage set by the
feedback resistors. In the case of an overvoltage event, the
IC will attempt to bring the output voltage back into
regulation by keeping the upper MOSFET turned off and
modulating the lower MOSFET for 2 consecutive PWM
cycles. If the overvoltage condition has not been corrected in
2 cycles, the ISL9440, ISL9440A and ISL9441 will turn on
the lower MOSFET until the overvoltage has been cleared,
or the power path is interrupted by opening a fuse.
Over-Temperature Protection
The IC incorporates an over-temperature protection circuit
that shuts the IC down when a die temperature of +150°C
is reached. Normal operation resumes when the die
temperatures drops below +130°C through the initiation of
a full soft-start cycle.
Feedback Loop Compensation
To reduce the number of external components and to simplify
the process of determining compensation components, all
PWM controllers have internally compensated error
amplifiers. To make internal compensation possible several
design measures were taken.
First, the ramp signal applied to the PWM comparator is
proportional to the input voltage provided via the VIN pin.
This keeps the modulator gain constant with variation in the
input voltage. Second, the load current proportional signal is
derived from the voltage drop across the lower MOSFET
during the PWM time interval and is subtracted from the
amplified error signal on the comparator input. This creates
an internal current control loop. The resistor connected to
the ISEN pin sets the gain in the current feedback loop. The
following expression estimates the required value of the
current sense resistor depending on the maximum operating
load current and the value of the MOSFET’s r
DS(ON)
.
Choosing R
CS
to provide 15μA of current to the current
sample and hold circuitry is recommended but values down
to 2μA and up to 100μA can be used. The higher sampling
current will help to stabilize the loop.
Due to the current loop feedback, the modulator has a single
pole response with -20dB slope at a frequency determined
by the load.
where R
O
is load resistance and C
O
is load capacitance. For
this type of modulator, a Type 2 compensation circuit is
usually sufficient.
R
OCSET
7
( )
R
OC
(
)
DS ON
(
)
)
------------------------------------------
=
(EQ. 5)
R
CS
I
----------------------------------------------
(
)
r
)
(
)
≥
(EQ. 6)
F
PO
O
O
--------------------------------
=
(EQ. 7)
ISL9440, ISL9440A, ISL9441
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9441 | Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller |
| ISL95810UIRT8 | Low Noise, Low Power I2C Bus, 256 Taps |
| ISL95810UIU8Z | Single Digitally Controlled Potentiometer (XDCP) |
| ISL95810 | Single Digitally Controlled Potentiometer (XDCP) |
| ISL95810WIU8Z | Single Digitally Controlled Potentiometer (XDCP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9440AEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL9440 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL9440AIRZ | 功能描述:IC REG QD BCK/LINEAR SYNC 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL9440AIRZ-T | 功能描述:IC REG QD BCK/LINEAR SYNC 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（2），線性（LDO）（1） 功能:任何功能 輸出數:3 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:4.5 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:28-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:* 包裝:帶卷 (TR) 其它名稱:ISL6402IVZ-TTR |
| ISL9440BEVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL9440B RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL9440BIRZ | 功能描述:IC REG QD BCK/LINEAR SYNC 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（2），線性（LDO）（1） 功能:任何功能 輸出數:3 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:4.5 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:28-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:* 包裝:帶卷 (TR) 其它名稱:ISL6402IVZ-TTR |
發布緊急采購，3分鐘左右您將得到回復。