- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL9217 (Intersil Corporation) 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set PDF資料下載
參數資料
| 型號： | ISL9217 |
| 廠商： | Intersil Corporation |
| 英文描述： | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| 中文描述： | 8至12芯鋰離子電池過電流保護和模擬前端芯片組 |
| 文件頁數： | 26/33頁 |
| 文件大?。?/td> | 645K |
| 代理商： | ISL9217 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
26
FN6488.1
November 2, 2007
User Flags
The ISL9216 and ISL9217 each contain four flags in the
register area that the microcontroller can use for general
purpose indicators. These bits are designated UFLG3, UFLG2,
UFLG1, and UFLG0. The microcontroller can set or reset these
bits by writing into the appropriate register.
The user flag bits are battery backed up, so the contents
remain even after a sleep mode. However, if the mirocontroller
sets the POR bit to force a power on reset, all of the user flags
will also be reset. In addition, if the voltage on cell1 ever drops
below the POR voltage, the contents of the user flags (as well
as all other register values) could be lost.
Serial Interface
INTERFACE CONVENTIONS
The device supports a bi-directional bus oriented protocol.
The protocol defines any device that sends data onto the
bus as a transmitter, and the receiving device as the
receiver. The device controlling the transfer is called the
master and the device being controlled is called the slave.
The master always initiates data transfers, and provides the
clock for both transmit and receive operations. Therefore,
the ISL9216 and ISL9217 devices operate as slaves in all
applications.
When sending or receiving data, the convention is the most
significant bit (MSB) is sent first. So, the first address bit sent
is bit 7.
CLOCK AND DATA
Data states on the SDA line can change only while SCL is
LOW. SDA state changes during SCL HIGH are reserved for
indicating start and stop conditions. See Figure 9.
START CONDITION
All commands are preceded by the start condition, which is a
HIGH to LOW transition of SDA when SCL is HIGH. The
device continuously monitors the SDA and SCL lines for the
start condition and will not respond to any command until
this condition has been met. See Figure 10.
STOP CONDITION
All communications must be terminated by a stop condition,
which is a LOW to HIGH transition of SDA when SCL is
HIGH. The stop condition is also used to place the device
into the Standby power mode after a read sequence. A stop
condition is only issued after the transmitting device has
released the bus. See Figure 10.
ACKNOWLEDGE
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, releases the bus after transmitting 8-bits.
During the ninth clock cycle, the receiver pulls the SDA line
LOW to acknowledge that it received the 8-bits of data. See
Figure 11.
The device responds with an acknowledge after recognition
of a start condition and the correct slave byte. If a write
operation is selected, the device responds with an
acknowledge after the receipt of each subsequent 8-bits.
The device acknowledges all incoming data and address
bytes, except for the slave byte when the contents do not
match the devices internal pattern.
In the read mode, the device transmits 8-bits of data,
releases the SDA line, then monitors the line for an
acknowledge. If an acknowledge is detected and no stop
condition is generated by the master, the device will
continues to transmit data. The device terminates further
data transmissions if an acknowledge is not detected. The
master must then issue a stop condition to return the device
to Standby mode and place the device into a known state.
WRITE OPERATIONS
For a write operation, the device requires a slave byte and an
address byte. The slave byte specifies which of the devices (in
a cascade configuration) the master is writing to. The address
specifies one of the registers in that device. After receipt of
each byte, the device responds with an acknowledge, and
awaits the next 8-bits from the master. After the acknowledge,
following the transfer of data, the master terminates the transfer
by generating a stop condition. See Figure 12.
SCL
SDA
DATA
STABLE
DATA
CHANGE
DATA
STABLE
FIGURE 9. VALID DATA CHANGES ON I
2
C BUS
SCL
SDA
START
STOP
FIGURE 10. I
2
C START AND STOP BITS
8
1
9
DATA OUTPUT
FROM
TRANSMITTER
DATA OUTPUT
FROM RECEIVER
START
ACKNOWLEDGE
FIGURE 11. ACKNOWLEDGE RESPONSE FROM RECEIVER
SCL FROM
MASTER
ISL9216, ISL9217
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9217IRZ | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| ISL95310 | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95310WIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95310UIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95311 | Terminal Voltage 0V to 13.2V, 128 Taps I2C Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9217IRZ | 功能描述:IC MULTI-CELL LI-ION PROT 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9217IRZ-T | 功能描述:IC MULTI-CELL LI-ION PROT 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9219AIRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219AIRZR5332 | 功能描述:IC BATT CHARGER LI-ION 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219AIRZ-T | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。