- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL9217 (Intersil Corporation) 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set PDF資料下載
參數資料
| 型號： | ISL9217 |
| 廠商： | Intersil Corporation |
| 英文描述： | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| 中文描述： | 8至12芯鋰離子電池過電流保護和模擬前端芯片組 |
| 文件頁數： | 23/33頁 |
| 文件大?。?/td> | 645K |
| 代理商： | ISL9217 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
23
FN6488.1
November 2, 2007
The load monitor circuit can be turned on or off by the
microcontroller. It is normally turned off to minimize current
consumption. It must be activated by the external
microcontroller for it to operate. The circuit works by
internally connecting the VMON pin to VSS through a
resistor. The circuit operates as shown in Figure 4.
In a typical pack operation, when an overcurrent or short
circuit event happens, the DFET turns off, opening the
battery circuit to the load. At this time, the R
L
is small and
the load monitor is initially off. In this condition, the voltage at
VMON could rise to nearly the pack voltage. However, since
in most configurations, this voltage would exceed the
maximum limits on the VMON pin, a series zener diode is
required.
Once the power FETs turn off, the microcontroller activates
the load monitor by setting the LDMONEN bit. This turns on
an internal FET that adds a pull-down resistor to the load
monitor circuit. While still in the overload condition the
combination of the load resistor, an external adjustment
resistor (R
1
), the zener diode, and the internal load monitor
resistor form a voltage divider. R
1
is chosen so that when the
load is released to a sufficient level, the LDFAIL condition is
reset.
OVER-TEMPERATURE SAFETY FUNCTIONS
External Temperature Control
The external temperature is monitored by using a voltage
divider consisting of a fixed resistor and a thermistor. This
divider is powered by the ISL9216 TEMP3V output. This
output is normally controlled so it is on for only short periods
to minimize current consumption.
Without microcontroller intervention, the ISL9216
continuously turns on TEMP3V output (and the external
temperature monitor) for 5ms every 640ms. In this way, the
external temperature is monitored even if the microcontroller
is asleep. If the ATMPOFF bit is set, this automatic
temperature scan is turned off.
When the TEMP3V output turns on, the ISL9216 waits 1ms
for the temperature reading to stabilize, then compares the
external temperature voltage with an internal voltage divider
that is set to TEMP3V/13. When the thermistor voltage is
below the reference threshold after the delay, an external
temperature fail condition exists. To set the external over-
temperature limit, set the value of R
X
resistor to the 12 times
the resistance of the thermistor at the over-temperature
threshold.
The TEMP3V output pin also turns on when the
microcontroller sets the AO3:AO0 bits to select that the
external temperature voltage. This causes the TEMPI voltage
to be placed on AO and activates (after 1ms) the over-
temperature detection. As long as the AO3:AO0 bits point to
the external temperature, the TEMP3V output remains on.
Because of the manual scan of the temperature, it may be
desired to turn off the automatic scan, although they can be
used at the same time without interference. To turn off the
automatic scan, set the ATMPOFF bit.
The microcontroller can over-ride both the automatic
temperature scan and the microcontroller controlled
temperature scan by setting the TEMP3ON configuration bit.
This turns on the TEMP3V output to keep the temperature
control voltage on all the time, for a continuous monitoring of
an over-temperature condition. This likely will consume a
significant amount of current, so this feature is usually used
for special or test purposes.
Protection
As a default, when the ISL9216 detects an internal or
external over-temperature condition, the FETs are turned off,
the cell balancing function is disabled, and the IOT bit or
XOT bit (respectively) is set.
Turning off the FETs in the event of an over-temperature
condition prevents continued discharge or charge of the cells
when they are over heated. Turning off the cell balancing in
the event of an over-temperature condition prevents damage
to the IC in the event too many cells are being balanced,
causing too much power dissipation in the ISL9216.
635ms
5ms
FIGURE 5. EXTERNAL TEMPERATURE MONITORING AND
CONTROL (ISL9216 ONLY)
AO
RGO
TEMP3V
TEMPI
VSS
I
2
C
MUX
I
2
C
TEMP
MONITOR
TEMP FAIL
INDICATOR
VSS (ON)
R
TMP3ON
AO3:AO0
DECODE
OSC
ATMPOFF
C
D
D
TO
μC
XOT
1
R
1ms
DELAY
EXTERNAL
EXT TEMP
O
P
R
X
ISL9216
ISL9216, ISL9217
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9217IRZ | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| ISL95310 | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95310WIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95310UIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95311 | Terminal Voltage 0V to 13.2V, 128 Taps I2C Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9217IRZ | 功能描述:IC MULTI-CELL LI-ION PROT 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9217IRZ-T | 功能描述:IC MULTI-CELL LI-ION PROT 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9219AIRZ | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219AIRZR5332 | 功能描述:IC BATT CHARGER LI-ION 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL9219AIRZ-T | 功能描述:IC CHRGR LI-ION SGL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。