- 您現在的位置：買賣IC網 > PDF目錄384531 > ISL9203R5220 (Intersil Corporation) RESISTOR 1.30M OHM 1/10W 1% 0603 PDF資料下載
參數資料
| 型號： | ISL9203R5220 |
| 廠商： | Intersil Corporation |
| 英文描述： | RESISTOR 1.30M OHM 1/10W 1% 0603 |
| 中文描述： | Li-ion/Li聚合物電池充電器 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 526K |
| 代理商： | ISL9203R5220 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁
14
FN6106.0
February 3, 2005
FAULT and STATUS Pull-Up Resistors
Both FAULT and STATUS pins are open-drain outputs that
need an external pull-up resistor. It is recommended that
both pins be pulled up to the input voltage or the 2.8V from
the V2P8 pin. If the indication pins have to be pulled up to
other voltages, the user needs to examine carefully whether
or not the ESD diodes will form a leakage current path to the
battery when the input power is removed. If the leakage path
does exist, an external transistor is required to break the
path.
Figure 24 shows the implementation. If the FAULT pin is
directly pulled up to the VCC voltage (not shown in Figure
24), a current will flow from the VCC to the FAULT pin, then
through the ESD diode to the VIN pin. Any leakage on the
VIN pin, caused by an external or internal current path, will
result in a current path from VCC to ground.
The N-channel MOSFET Q
1
buffers the FAULT pin. The
gate of Q
1
is connected to VIN or the V2P8 pin. When the
FAULT pin outputs a logic low signal, Q
1
is turned on and its
drain outputs a low signal as well. When FAULT is high
impedance, R
1
pulls the Q
1
drain to high. When the input
power is removed, the Q
1
gate voltage is also removed, thus
the Q
1
drain stays high.
Shutdown
The ISL9203 can be shutdown by pulling the EN pin to
ground. When shut down, the charger draws typically less
than 30
μ
A current from the input power and the 2.8V output
at the V2P8 pin is also turned off. The EN pin needs be
driven with an open-drain or open-collector logic output, so
that the EN pin is floating when the charger is enabled. If the
EN pin is driven by an external source, the POR threshold
voltage will be affected.
Input and Output Capacitor Selection
Typically any type of capacitors can be used for the input
and the output. Use of a 0.47
μ
F or higher value ceramic
capacitor for the input is recommended. When the battery is
attached to the charger, the output capacitor can be any
ceramic type with the value higher than 0.1
μ
F. However, if
there is a chance the charger will be used as an LDO linear
regulator, a 10
μ
F tantalum capacitor is recommended. Note
that the charger always steps through the 15-cycle V
MIN
verification time before the charge current rises to the
constant charge current, as discussed earlier. Hence, when
using as an LDO, the system should make sure not to load
the charger heavily until the 15-cycle verification is
completed.
Working with Current-Limited Adapter
The ISL9203 can work with a current-limited adapter to
significantly reduce the thermal dissipation during charging.
Refer to the ISL6292 data sheet, which can be found at
http://www.intersil.com, for more details.
Board Layout Recommendations
The ISL9203 internal thermal foldback function limits the
charge current when the internal temperature reaches
approximately 100°C. In order to maximize the current
capability, it is very important that the exposed pad under the
TABLE 4. STATUS INDICATIONS
FAULT STATUS
INDICATION
High
High
Charge completed with no fault (Inhibit) or
Standby
High
Low
Charging in one of the three modes
Low
High
Fault
NOTE: Both outputs are pulled up with external resistors.
FIGURE 23. THE V2P8 PIN OUTPUT vs THE INPUT VOLTAGE
AT THE VIN PIN. VERTICAL: 1V/DIV,
HORIZONTAL: 100ms/DIV
3.4V
2.4V
2.8V
V
IN
V2P8
FIGURE 24. PULL-UP CIRCUIT TO AVOID BATTERY LEAKAGE
CURRENT IN THE ESD DIODES.
FAULT
VIN
VIN
ESD Diode
C
EN
VCC
GND
VIN or
V2P8
STATUS
R
1
Note:
R
is approximately 240k
when EN is floating and is
approximately 140k
when the EN is grounded.
R
LKG
Q
1
ISL9203
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9203CRZ-TR5220 | Li-ion/Li Polymer Battery Charger |
| ISL9203CRZ | Li-ion/Li Polymer Battery Charger |
| ISL9203CRZ-T | Li-ion/Li Polymer Battery Charger |
| ISL9204 | High Input Voltage Charger |
| ISL9204IRZ-T | High Input Voltage Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9203R5220_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL9204 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High Input Voltage Charger |
| ISL9204EVAL1 | 功能描述:EVALUATION BOARD 1 ISL9204 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL9204EVAL1Z | 制造商:Intersil Corporation 功能描述:EVAL BD FOR ISL9204, HIGH INPUT VOLT CHGR - Bulk |
| ISL9204IRZ-T | 功能描述:IC VOLTAGE CHARGER LI-ION 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
發布緊急采購，3分鐘左右您將得到回復。