- 您現在的位置：買賣IC網 > PDF目錄384531 > ISL9203R5220 (Intersil Corporation) RESISTOR 1.30M OHM 1/10W 1% 0603 PDF資料下載
參數資料
| 型號： | ISL9203R5220 |
| 廠商： | Intersil Corporation |
| 英文描述： | RESISTOR 1.30M OHM 1/10W 1% 0603 |
| 中文描述： | Li-ion/Li聚合物電池充電器 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 526K |
| 代理商： | ISL9203R5220 |
10
FN6106.0
February 3, 2005
Theory of Operation
The ISL9203 is an integrated charger for single-cell Li-ion or
Li-polymer batteries. The ISL9203 functions as a traditional
linear charger when powered with a voltage-source adapter.
When powered with a current-limited adapter, the charger
minimizes the thermal dissipation commonly seen in
traditional linear chargers.
As a linear charger, the ISL9203 charges a battery in the
popular constant current (CC) and constant voltage (CV)
profile. The constant charge current I
REF
is programmable
up to 1.5A with an external resistor. The charge voltage V
CH
has 1% accuracy over the entire recommended operating
condition range. The charger always preconditions the
battery with 10% of the programmed current at the beginning
of a charge cycle, until the battery voltage is verified to be
above the minimum fast charge voltage, V
MIN
. This low-
current preconditioning charge mode is named trickle mode.
The verification takes 15 cycles of an internal oscillator
whose period is programmable with the timing capacitor. A
thermal-foldback feature removes the thermal concern
typically seen in linear chargers. The charger reduces the
charge current automatically as the IC internal temperature
rises above 100°C to prevent further temperature rise. The
thermal-foldback feature guarantees safe operation when
the printed circuit board (PCB) is space limited for thermal
dissipation.
The charger offers a safety timer for setting the fast charge
time (TIMEOUT) limit to prevent charging a dead battery for
an extensively long time. The trickle mode is limited to 1/8 of
TIMEOUT.
The charger automatically re-charges the battery when the
battery voltage drops below a recharge threshold. When the
wall adapter is not present, the ISL9203 draws less than 1
μ
A
current from the battery.
Three indication pins are available from the charger to
indicate the charge status. The V2P8 outputs a 2.8V dc
voltage when the input voltage is above the power-on reset
(POR) level and can be used as the power-present
indication. This pin is capable of sourcing a 2mA current, so
it can also be used to bias external circuits.
The STATUS pin is an open-drain logic output that turns
LOW at the beginning of a charge cycle until the end-of-
charge (EOC) condition is qualified. The EOC condition is:
the battery voltage rises above the recharge threshold and
the charge current falls below a user-programmable EOC
current threshold. Once the EOC condition is qualified, the
STATUS output rises to HIGH and is latched. The latch is
released at the beginning of a charge or re-charge cycle.
The open-drain FAULT pin turns low when a charge time
fault occurs or when the IREF pin is pulled below 0.35V or
above 1.4V.
Figure 18 shows the typical charge curves in a traditional
linear charger powered with a constant-voltage adapter.
From the top to bottom, the curves represent the constant
input voltage, the battery voltage, the charge current and the
power dissipation in the charger. The power dissipation P
CH
is given by the following equation:
(EQ. 1)
where I
CHARGE
is the charge current. The maximum power
dissipation occurs during the beginning of the CC mode. The
maximum power the IC is capable of dissipating is
dependent on the thermal impedance of the printed-circuit
board (PCB). Figure 18 shows, with dotted lines, two cases
that the charge currents are limited by the maximum power
dissipation capability due to the thermal foldback.
FIGURE 18. TYPICAL CHARGE CURVES USING A
CONSTANT-VOLTAGE ADAPTER
V
CH
V
MIN
V
IN
I
REF
I
REF
/10
P
1
P
2
P
3
Trickle
Mode
Constant Current
Mode
Constant Voltage
Mode
Inhibit
TIMEOUT
Input Voltage
Battery Voltage
Charge Current
Power Dissipation
P
CH
V
IN
V
BAT
–
(
)
I
CHARGE
=
FIGURE 19. TYPICAL CHARGE CURVES USING A CURRENT-
LIMITED ADAPTER
V
CH
V
MIN
V
IN
I
REF
I
LIM
I
REF
/10
P
1
P
2
Trickle
Mode
Constant Current
Mode
Constant Voltage
Mode
Inhibit
TIMEOUT
Input Voltage
Battery Voltage
Charge Current
Power Dissipation
ISL9203
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9203CRZ-TR5220 | Li-ion/Li Polymer Battery Charger |
| ISL9203CRZ | Li-ion/Li Polymer Battery Charger |
| ISL9203CRZ-T | Li-ion/Li Polymer Battery Charger |
| ISL9204 | High Input Voltage Charger |
| ISL9204IRZ-T | High Input Voltage Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9203R5220_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL9204 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High Input Voltage Charger |
| ISL9204EVAL1 | 功能描述:EVALUATION BOARD 1 ISL9204 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL9204EVAL1Z | 制造商:Intersil Corporation 功能描述:EVAL BD FOR ISL9204, HIGH INPUT VOLT CHGR - Bulk |
| ISL9204IRZ-T | 功能描述:IC VOLTAGE CHARGER LI-ION 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
發布緊急采購，3分鐘左右您將得到回復。