- 您現在的位置：買賣IC網 > PDF目錄384531 > ISL9203ACRZ (INTERSIL CORP) Li-ion/Li Polymer Battery Charger PDF資料下載
參數資料
| 型號： | ISL9203ACRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Li-ion/Li Polymer Battery Charger |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | 3 X 3 MM, ROHS COMPLIANT, PLASTIC, DFN-10 |
| 文件頁數： | 6/14頁 |
| 文件大小： | 320K |
| 代理商： | ISL9203ACRZ |
6
FN6430.0
February 14, 2007
Pin Descriptions
VIN (Pin1)
VIN is the input power source. Connect to a wall adapter.
NC (Pin 2)
No connection for this pin.
STATUS (Pin 3)
STATUS is an open-drain output indicating charging and
inhibit states. The STATUS pin is pulled LOW when the
charger is charging a battery. It will be forced to high
impedence when the charge current drops to I
MIN
. This high
impedence mode will be latched until a recharge cycle or a
new charge cycle starts.
TIME (Pin 4)
The TIME pin determines the oscillation period by
connecting a timing capacitor between this pin and GND.
The oscillator also provides a time reference for the charger.
GND (Pin 5)
GND is the connection to system ground.
EN (Pin 6)
EN is the enable logic input. Connect the EN pin to LOW to
disable the charger or leave it floating to enable the charger.
V2P8 (Pin 7)
This is a 2.8V reference voltage output. This pin outputs a
2.8V voltage source when the input voltage is above POR
threshold, otherwise it outputs zero. The V2P8 pin can be
used as an indication for adapter presence.
IREF
(Pin 8)
This is the programming input for the constant charging
current. It maintains at 0.8V when the charger is in normal
operation.
VSEN (Pin 9)
VSEN is the remote voltage sense pin. Connect this pin as
close as possible to the battery pack positive connection. If
the VSEN pin is floating, its voltage drops to zero volt and
the charger operates in the trickle mode.
VBAT (Pin 10)
VBAT is the connection to the battery. Typically a 10μF
Tantalum capacitor is needed for stability when there is no
battery attached. When a battery is attached, only a 0.1μF
ceramic capacitor is required.
FIGURE 15. STATUS PIN VOLTAGE vs CURRENT WHEN THE OPEN-DRAIN MOSFET TURNS ON
Typical Operating Performance
The test conditions for the Typical Operating Performance are: V
IN
= 5V, T
A
= +25°C,
R
IREF
= R
IMIN
= 80k
Ω
, V
BAT
= 3.7V, unless otherwise noted.
(Continued)
0
4
8
12
16
20
24
28
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
STATUS PIN VOLTAGE (V)
S
ISL9203A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9203ACRZ-T | Li-ion/Li Polymer Battery Charger |
| ISL9203 | Li-ion/Li Polymer Battery Charger |
| ISL9203CRZR5220 | PT 32C 32#20 PIN RECP |
| ISL9203R5220 | RESISTOR 1.30M OHM 1/10W 1% 0603 |
| ISL9203CRZ-TR5220 | Li-ion/Li Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9203ACRZ-T | 功能描述:IC CHRGR LI-ION/LI SGL 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9203CRZ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL9203CRZR5220 | 功能描述:IC BATT CHARGER LI-ION 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ISL9203CRZ-T | 制造商:Intersil 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL9203CRZ-TR5220 | 功能描述:IC BATT CHARGER LI-ION 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。