- 您現在的位置：買賣IC網 > PDF目錄384529 > ISL88731 (Intersil Corporation) SMBus Level 2 Battery Charger PDF資料下載
參數資料
| 型號： | ISL88731 |
| 廠商： | Intersil Corporation |
| 英文描述： | SMBus Level 2 Battery Charger |
| 中文描述： | 2級的SMBus電池充電器 |
| 文件頁數： | 21/22頁 |
| 文件大?。?/td> | 474K |
| 代理商： | ISL88731 |
21
FN9258.0
November 20, 2006
Signal Ground and Power Ground Connection
At minimum, a reasonably large area of copper, which will
shield other noise couplings through the IC, should be used
as signal ground beneath the IC. The best tie-point between
the signal ground and the power ground is at the negative
side of the output capacitor on each side, where there is little
noise; a noisy trace beneath the IC is not recommended.
GND and VCC Pin
At least one high quality ceramic decoupling cap should be
used to cross these two pins. The decoupling cap can be put
close to the IC.
LGATE Pin
This is the gate drive signal for the bottom MOSFET of the
buck converter. The signal going through this trace has both
high dv/dt and high di/dt, and the peak charging and
discharging current is very high. These two traces should be
short, wide, and away from other traces. There should be no
other traces in parallel with these traces on any layer.
PGND Pin
PGND pin should be laid out to the negative side of the
relevant output cap with separate traces.The negative side
of the output capacitor must be close to the source node of
the bottom MOSFET. This trace is the return path of LGATE.
PHASE Pin
This trace should be short, and positioned away from other
weak signal traces. This node has a very high dv/dt with a
voltage swing from the input voltage to ground. No trace
should be in parallel with it. This trace is also the return path
for UGATE. Connect this pin to the high-side MOSFET
source.
UGATE Pin
This pin has a square shape waveform with high dv/dt. It
provides the gate drive current to charge and discharge the
top MOSFET with high di/dt. This trace should be wide,
short, and away from other traces, similar to the LGATE.
BOOT Pin
This pin’s di/dt is as high as the UGATE; therefore, this trace
should be as short as possible.
CSOP, CSON, CSSP and CSSN Pins
Accurate charge current and adapter current sensing is
critical for good performance. The current sense resistor
connects to the CSON and the CSOP pins through a low
pass filter with the filter cap very near the IC (see Figure 2).
Traces from the sense resister should start at the pads of the
sense resister and should be routed close together, through
the low pass filter and to the CSOP and CSON pins (see
Figure 26). The CSON pin is also used as the battery voltage
feedback. The traces should be routed away from the high
dv/dt and di/dt pins like PHASE, BOOT pins. In general, the
current sense resistor should be close to the IC. These
guidelines should also be followed for the adapter current
sense resister and CSSP and CSSN. Other layout
arrangements should be adjusted accordingly.
DCIN Pin
This pin connects to AC adapter output voltage, and should
be less noise sensitive.
Copper Size for the Phase Node
The capacitance of PHASE should be kept very low to
minimize ringing. It would be best to limit the size of the
PHASE node copper in strict accordance with the current
and thermal management of the application.
Identify the Power and Signal Ground
The input and output capacitors of the converters, the source
terminal of the bottom switching MOSFET PGND should
connect to the power ground. The other components should
connect to signal ground. Signal and power ground are tied
together at one point.
Clamping Capacitor for Switching MOSFET
It is recommended that ceramic caps be used closely
connected to the drain of the high-side MOSFET, and the
source of the low-side MOSFET. This capacitor reduces the
noise and the power loss of the MOSFET.
FIGURE 26. CURRENT SENSE RESISTOR LAYOUT
HIGH
CURRENT
TRACE
HIGH
CURRENT
TRACE
KELVIN CONNECTION TRACES
TO THE LOW PASS FILTER AND
CSOP AND CSON
SENSE
RESISTER
ISL88731
相關PDF資料 |
PDF描述 |
|---|---|
| ISL88731HRZ | SMBus Level 2 Battery Charger |
| ISL88731HRZ-T | SMBus Level 2 Battery Charger |
| ISL89400 | 100V, 1.25A Peak, High Frequency Half-Bridge Drivers |
| ISL89400AR3Z | 100V, 1.25A Peak, High Frequency Half-Bridge Drivers |
| ISL89401AR3Z | 100V, 1.25A Peak, High Frequency Half-Bridge Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL88731AHRZ | 功能描述:電池管理 ISL88731A NOTEBOOK BATRY CHRGRRE-BRAND RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| ISL88731AHRZ | 制造商:Intersil Corporation 功能描述:IC BATTERY CHARGER LI-ION 8A TQFN-28 |
| ISL88731AHRZ-T | 功能描述:IC BATTERY CHRGR SMBUS 28-TQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監(jiān)控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL88731CEVAL2Z | 功能描述:EVALUATION BOARD ISL88731 RoHS:是 類別:編程器，開發(fā)系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發(fā)器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL88731CHRTZ | 制造商:Intersil Corporation 功能描述:PB-FREE ISL88731C NOTEBOOK BATTERY CHARGER (P6 SHRINK) - Rail/Tube 制造商:Intersil 功能描述:ISL88731C NOTEBOOK BATRY CHRGRP6 SHRINK |
發(fā)布緊急采購，3分鐘左右您將得到回復。