- 您現在的位置：買賣IC網 > PDF目錄384528 > ISL8500 (Intersil Corporation) Switching Regulator Control (Voltage Mode type AC/DC) ; Vin (V) max.: 10 to 35; Icc (mA) max.: 15; Fmax (kHz) max.: 500; Topr [Tjopr] (°C): -30 to +85; Remarks: Primary control MOSFET drive; Package: SOP; Pin count: 20 PDF資料下載
參數資料
| 型號： | ISL8500 |
| 廠商： | Intersil Corporation |
| 英文描述： | Switching Regulator Control (Voltage Mode type AC/DC) ; Vin (V) max.: 10 to 35; Icc (mA) max.: 15; Fmax (kHz) max.: 500; Topr [Tjopr] (°C): -30 to +85; Remarks: Primary control MOSFET drive; Package: SOP; Pin count: 20 |
| 中文描述： | 甲標準降壓PWM穩壓器 |
| 文件頁數： | 6/15頁 |
| 文件大?。?/td> | 622K |
| 代理商： | ISL8500 |
6
FN6611.0
December 10, 2007
Pin Descriptions
FB (Pin 1) and COMP (Pin 2)
The standard buck regulator employs a single voltage
control loop. FB is the negative input to the voltage loop error
amplifier. COMP is the output of the error amplifier. The
output voltage is set by an external resistor divider
connected to FB. With a properly selected divider, the output
voltage can be set to any voltage between the power rail
(reduced by converter losses) and the 0.6V reference.
Connecting an AC network across COMP and FB provides
loop compensation to the amplifier.
In addition, the PWM regulator power good and
undervoltage protection circuitry use FB to monitor the
regulator output voltage.
SS (Pin 3)
Program pin for soft-start duration. A regulated 30μA pull-up
current source charges a capacitor connected from the pin to
GND. The output voltage of the converter follows the
ramping voltage on the SS pin.
EN (Pin 4)
PWM controller enable input. The PWM converter output is
held off when the pin is pulled to ground. When the voltage
on this pin rises above 1.7V, the chip is enabled.
PG (Pin 5)
PWM converter power good output. Open drain logic output
that is pulled to ground when the output voltage is outside
regulation limits. Connect a 100k
Ω
resistor from this pin to
VDD. Pin is low when the buck regulator output voltage is
not within 10% of the respective nominal voltage, or during
the soft-start interval. Pin is high impedance when the output
is within regulation.
GND (Pin 6)
Ground connect for the IC and thermal relief for the package.
The exposed pad must be connected to GND and soldered
to the PCB. All voltage levels are measured with respect to
this pin.
VDD (Pin 7)
Internal 5V linear regulator output provides bias to all the
internal control logic. The ISL8500 may be powered directly
from a 5V (±10%) supply at this pin. When used as a 5V supply
input, this pin must be externally connected to VIN. The VDD
pin must always be decoupled to GND with a ceramic bypass
capacitor (minimum 1μF) located close to the pin.
BOOT (Pin 8)
Floating bootstrap supply pin for the power MOSFET gate
driver. The bootstrap capacitor provides the necessary
charge to turn and hold on the internal N-Channel MOSFET.
Connect an external capacitor from this pin to PHASE.
PHASE (Pins 9, 10)
Switch node connections to internal power MOSFET source,
external output inductor and external diode cathode.
VIN (Pins 11, 12)
The input supply for the PWM regulator power stage and the
source for the internal linear regulator that provides bias for
the IC. Place a ceramic capacitor from VIN to GND, close to
the IC for decoupling (typical 10μF).
TABLE 1. INPUT SUPPLY CONFIGURATION
INPUT
PIN CONFIGURATION
5.5V to 25V
Connect the input supply to the VIN pin only. The
VDD pin will provide a 5V output from the internal
linear regulator.
5V ±10%
Connect the input supply to the VIN and VDD pins.
ISL8500
相關PDF資料 |
PDF描述 |
|---|---|
| ISL8500IRZ | Switching Regulator Control (Voltage Mode type AC/DC) ; Vin (V) max.: 10 to 35; Icc (mA) max.: 15; Fmax (kHz) max.: 500; Topr [Tjopr] (°C): -30 to +85; Remarks: Primary control MOSFET drive; Package: DIP; Pin count: 16 |
| ISL8502 | 2.5A Synchronous Buck Regulator with Integrated MOSFETs |
| ISL8502IRZ | 2.5A Synchronous Buck Regulator with Integrated MOSFETs |
| ISL8560MREP | DC/DC Power Switching Regulator |
| ISL8560 | DC/DC Power Switching Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL85001EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL85001 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL85001IRZ | 功能描述:IC REG BUCK ADJ 1A 12DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:1 系列:EZBuck™ 類型:降壓（降壓） 輸出類型:可調式 輸出數:1 輸出電壓:0.8 V ~ 22.1 V 輸入電壓:3 V ~ 26 V PWM 型:電流模式 頻率 - 開關:1.5MHz 電流 - 輸出:1.8A 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 包裝:剪切帶 (CT) 供應商設備封裝:8-DFN（2x2） 其它名稱:785-1276-1 |
| ISL85001IRZ-T | 功能描述:IC REG BUCK ADJ 1A 12DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:兩者兼有 輸出數:1 輸出電壓:5V，1 V ~ 10 V 輸入電壓:3.5 V ~ 28 V PWM 型:電流模式 頻率 - 開關:220kHz ~ 1MHz 電流 - 輸出:600mA 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:16-QSOP |
| ISL8500EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL8500 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL8500EVAL2Z | 功能描述:EVAL BOARD 2 FOR ISL8500 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。