- 您現在的位置：買賣IC網 > PDF目錄384528 > ISL6745 (Intersil Corporation) Octal Buffers/Drivers With 3-State Outputs 20-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6745 |
| 廠商： | Intersil Corporation |
| 英文描述： | Octal Buffers/Drivers With 3-State Outputs 20-SOIC -40 to 85 |
| 中文描述： | 橋控制器精密死區時間控制 |
| 文件頁數： | 6/8頁 |
| 文件大小： | 226K |
| 代理商： | ISL6745 |
6
Pin Descriptions
V
DD
-
V
DD
is the power connection for the IC. To optimize
noise immunity, bypass V
DD
to GND with a ceramic
capacitor as close to the V
DD
and GND pins as possible.
The total supply current, I
DD
, will be dependent on the load
applied to outputs OUTA and OUTB. Total I
DD
current is the
sum of the quiescent current and the average output current.
Knowing the operating frequency, F
SW
, and the output
loading capacitance charge, Q, per output, the average
output current can be calculated from:
R
TD
-
This is the oscillator timing capacitor discharge current
control pin. A resistor is connected between this pin and
GND. The current flowing through the resistor determines
the magnitude of the discharge current. The discharge
current is nominally 55x this current. The PWM deadtime is
determined by the timing capacitor discharge duration.
C
T
-
The oscillator timing capacitor is connected between
this pin and GND.
CS -
This is the input to the overcurrent protection comparator.
The overcurrent comparator threshold is set at 0.600V nominal.
The CS pin is shorted to GND at the end of each switching
cycle. Depending on the current sensing source impedance, a
series input resistor may be required due to the delay between
the internal clock and the external power switch.
Exceeding the overcurrent threshold will start a delayed
shutdown sequence. Once an overcurrent condition is
detected, the soft-start charge current source is disabled.
The soft-start capacitor begins discharging through a 15μA
current source, and if it discharges to less than 3.9V
(Sustained Overcurrent Threshold), a shutdown condition
occurs and the OUTA and OUTB outputs are forced low.
When the soft-start voltage reaches 0.27V (Reset
Threshold) a soft-start cycle begins.
If the overcurrent condition ceases, and then an additional
50μs period elapses before the shutdown threshold is
reached, no shutdown occurs. The SS charging current is re-
enabled and the soft-start voltage is allowed to recover.
GND -
Reference and power ground for all functions on this
device. Due to high peak currents and high frequency
operation, a low impedance layout is necessary. Ground
planes and short traces are highly recommended.
OUTA and OUTB -
Alternate half cycle output stages. Each
output is capable of 1A peak currents for driving power
MOSFETs or MOSFET drivers. Each output provides very
low impedance to overshoot and undershoot.
SS -
Connect the soft-start timing capacitor between this pin
and GND to control the duration of soft-start. The value of the
capacitor determines the rate of increase of the duty cycle
during start-up, controls the overcurrent shutdown delay, and
the overcurrent and short circuit hiccup restart period.
V
ERR
- The inverting input of the PWM comparator. The
error voltage is applied to this pin to control the duty cycle.
Increasing the signal level increases the duty cycle. The
node may be driven with an external error amplifier or an
opto-coupler.
V
DDP
-
V
DDP
is the separate collector supply to the gate
drive. Having a separate V
DDP
pin helps isolate the analog
circuitry from the high power gate drive noise.
Functional Description
Features
The ISL6745 PWM is an excellent choice for low cost bridge
topologies for applications requiring accurate frequency and
deadtime control. Among its many features are 1A FET
drivers, adjustable soft-start, overcurrent protection and
internal thermal protection, allowing a highly flexible design
with minimal external components.
Oscillator
The ISL6745 has an oscillator with a frequency range to
2MHz, programmable using a resistor R
TD
and capacitor C
T
.
The switching period may be considered to be the sum of
the timing capacitor charge and discharge durations. The
charge duration is determined by C
T
and the internal current
source (assumed to be 160
μ
A
in the formula). The discharge
duration is determined by R
TD
and C
T
.
4
×
10
C
T
s
where T
C
and T
D
are the approximate charge and discharge
times, respectively, T
OSC
is the oscillator free running
period, and F
OSC
is the oscillator frequency. One output
switching cycle requires two oscillator cycles. The actual
times will be slightly longer than calculated due to internal
propagation delays of approximately 5ns/transition. This
delay adds directly to the switching duration, and also
causes overshoot of the timing capacitor peak and valley
voltage thresholds, effectively increasing the peak-to-peak
voltage on the timing capacitor. Additionally, if very low
charge and discharge currents are used, there will be an
increased error due to the input impedance at the C
T
pin.
The above formulae help with the estimation of the
frequency. Practically, effects like stray capacitances that
affect the overall C
T
capacitance, variation in R
TD
voltage
and charge current over temperature, etc. exist, and are best
evaluated in-circuit. Equation 2 follows from the basic
capacitor current equation,
i
=
. In this case, with
(EQ. 1)
I
OUT
2
Q
F
SW
=
A
T
C
1.25
≈
(EQ. 2)
T
D
----------------------------------------------------------------------------
R
TD
C
T
≈
s
(EQ. 3)
T
OSC
T
C
T
D
+
F
OSC
---------------
=
=
s
(EQ. 4)
C
t
d
d
V
×
ISL6745
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6752 | Octal Buffers/Drivers With 3-State Outputs 20-PDIP -40 to 85 |
| ISL6752AAZA-T | ZVS Full-Bridge Current-Mode PWM with Adjustable Synchronous Rectifier Control |
| ISL6752AAZA | Octal Buffers/Drivers With 3-State Outputs 20-PDIP -40 to 85 |
| ISL6753 | Octal Buffers/Drivers With 3-State Outputs 20-SO -40 to 85 |
| ISL6753AAZA-T | ZVS Full-Bridge PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6745AAUZ | 功能描述:IC REG CTRLR PWM VM 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6745AAUZ-T | 功能描述:IC REG CTRLR PWM VM 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6745AAUZ-TS2712 | 功能描述:IC REG CTRLR PWM VM 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6745ALEVAL3Z | 功能描述:EVAL BOARD 3 FOR ISL6745 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6745AU | 功能描述:IC REG CTRLR PWM VM 10-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。