- 您現在的位置：買賣IC網 > PDF目錄383154 > ISL6532CCRZ-T (INTERSIL CORP) R8C Series, 21 Group, WDTO 48P6Q-A PDF資料下載
參數資料
| 型號： | ISL6532CCRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | R8C Series, 21 Group, WDTO 48P6Q-A |
| 中文描述： | SWITCHING CONTROLLER, 280 kHz SWITCHING FREQ-MAX, PQCC28 |
| 封裝： | 6 X 6 MM, LEAD FREE, PLASTIC, MO-220VJJC, QFN-28 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 506K |
| 代理商： | ISL6532CCRZ-T |
10
Had the cause of the over current still been present after the
delay interval, the over current condition would be sensed
and the regulator would be shut down again for another
delay interval of three soft start cycles. The resulting hiccup
mode style of protection would continue to repeat indefinitely.
The over-current function will trip at a peak inductor current
(I
PEAK)
determined by:
where I
OCSET
is the internal OCSET current source (20
μ
A
typical). The OC trip point varies mainly due to the MOSFET
r
DS(ON)
variations. To avoid over-current tripping in the
normal operating load range, find the R
OCSET
resistor from
the equation above with:
1. The maximum r
DS(ON)
at the highest junction
temperature.
2. The minimum I
OCSET
from the specification table.
3. Determine I
PEAK
for:
I
)
2
, where
I is
the output inductor ripple current.
For an equation for the ripple current see the section under
component guidelines titled ‘Output Inductor Selection’.
A small ceramic capacitor should be placed in parallel with
R
OCSET
to smooth the voltage across
R
OCSET
in the
presence of switching noise on the input voltage.
V
TT
Over Current Protection
The internal V
TT
LDO is protected from fault conditions
through a 3.3A current limit. This current limit protects the
ISL6532C if the LDO is sinking or sourcing current. During
an overcurrent event on the V
TT
LDO, only the V
TT
LDO is
disabled. Once the over current condition on the V
TT
rail is
removed, V
TT
will recover.
Over/Under Voltage Protection
All three regulators are protected from faults through internal
Over/Under voltage detection circuitry. If the any rail falls
below 85% of the targeted voltage, then an undervoltage
event is tripped. An under voltage will disable all three
regulators for a period of 3 soft-start cycles, after which a
normal soft-start is initiated. If the output is still under 85% of
target, the regulators will continue to be disabled and soft-
started in a hiccup mode until the fault is cleared. This
protection feature works much the same as the VDDQ PWM
over current protection works. See Figure 3.
If the any rail exceeds 115% of the targeted voltage, then all
three outputs are immediately disabled. The ISL6532C will
not re-enable the outputs until either the bias voltage is
toggled in order to initiate a POR or the S5 signal is forced
LOW and then back to HIGH.
Thermal Protection (S0/S3 State)
If the ISL6532C IC junction temperature reaches a nominal
temperature of 140
o
C, all regulators will be disabled. The
ISL6532C will not re-enable the outputs until the junction
temperature drops below 110
o
C and either the bias voltage
is toggled in order to initiate a POR or the SLP_S5 signal is
forced LOW and then back to HIGH.
Shoot-Through Protection
A shoot-through condition occurs when both the upper and
lower MOSFETs are turned on simultaneously, effectively
shorting the input voltage to ground. To protect from a shoot-
through condition, the ISL6532C incorporates specialized
circuitry which insures that complementary MOSFETs are
not ON simultaneously.
The adaptive shoot-through protection utilized by the V
DDQ
regulator looks at the lower gate drive pin, LGATE, and the
upper gate drive pin, UGATE, to determine whether a
MOSFET is ON or OFF. If the voltage from UGATE or from
LGATE to GND is less than 0.8V, then the respective
MOSFET is defined as being OFF and the other MOSFET is
allowed to turned ON. This method allows the V
DDQ
regulator to both source and sink current.
Since the voltage of the MOSFET gates are being measured
to determine the state of the MOSFET, the designer is
encouraged to consider the repercussions of introducing
external components between the gate drivers and their
respective MOSFET gates before actually implementing
such measures. Doing so may interfere with the shoot-
through protection.
TIME
T1
T0
T2
500mV/DIV
V
DDQ
V
AGP
V
TT
FIGURE 3. V
DDQ
and V
TT
OVER CURRENT PROTECTION
AND V
TT
/V
AGP
LDO UNDER VOLTAGE
PROTECTION RESPONSES
INTERNAL SOFT-START FUNCTION
DELAY INTERVAL
I
PEAK
I
x R
DS ON
)
--------------r
=
I
PEAK
I
OUT MAX
)
----------
+
>
ISL6532C
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6532C | PWM Control Circuit 16-SOIC 0 to 70 |
| ISL6532CCR | PWM Control Circuit 16-SOIC 0 to 70 |
| ISL6532CCR-T | PWM Control Circuit 16-SOIC 0 to 70 |
| ISL6532CCRZ | PWM Control Circuit 16-SOIC 0 to 70 |
| ISL6532 | ACPI Regulator/Controller for Dual Channel DDR Memory Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6532CR | 功能描述:IC REG/CTRLR ACPI DUAL DDR 20QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6532CR-T | 功能描述:IC REG/CTRLR ACPI DUAL DDR 20QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6532CRZ | 功能描述:IC CTRLR PWM 2CHAN DDR 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| ISL6532CRZ-T | 功能描述:IC REG/CTRLR ACPI DUAL DDR 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6532EVAL1 | 功能描述:EVAL BOARD 1 FOR ISL6532 RoHS:否 類別:編程器，開發系統 >> 評估板 - 線性穩壓器 (LDO) 系列:* 產品變化通告:1Q2012 Discontinuation 30/Mar/2012 設計資源:NCP590MNDPTAGEVB Gerber Files 標準包裝:1 系列:- 每 IC 通道數:2 - 雙 輸出電壓:1.8V，2.8V 電流 - 輸出:300mA 輸入電壓:2.1 ~ 5.5 V 穩壓器類型:正，固定式 工作溫度:-40°C ~ 85°C 板類型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名稱:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
發布緊急采購，3分鐘左右您將得到回復。