- 您現在的位置：買賣IC網 > PDF目錄383154 > ISL6532B (Intersil Corporation) PWM Control Circuit 16-SSOP 0 to 70 PDF資料下載
參數資料
| 型號： | ISL6532B |
| 廠商： | Intersil Corporation |
| 英文描述： | PWM Control Circuit 16-SSOP 0 to 70 |
| 中文描述： | ACPI的穩壓器/雙通道DDR內存控制器系統 |
| 文件頁數： | 10/15頁 |
| 文件大小： | 362K |
| 代理商： | ISL6532B |
10
spikes can degrade efficiency, radiate noise into the circuit,
and lead to device over-voltage stress. Careful component
layout and printed circuit board design minimizes these
voltage spikes.
As an example, consider the turn-off transition of the upper
MOSFET. Prior to turn-off, the MOSFET is carrying the full
load current. During turn-off, current stops flowing in the
MOSFET and is picked up by the lower MOSFET. Any
parasitic inductance in the switched current path generates a
large voltage spike during the switching interval. Careful
component selection, tight layout of the critical components,
and short, wide traces minimizes the magnitude of voltage
spikes.
There are two sets of critical components in the ISL6532B
switching converter. The switching components are the most
critical because they switch large amounts of energy, and
therefore tend to generate large amounts of noise. Next are
the small signal components which connect to sensitive
nodes or supply critical bypass current and signal coupling.
A multi-layer printed circuit board is recommended. Figure 4
shows the connections of the critical components in the
converter. Note that capacitors C
IN
and C
OUT
could each
represent numerous physical capacitors. Dedicate one solid
layer, usually a middle layer of the PC board, for a ground
plane and make all critical component ground connections
with vias to this layer. Dedicate another solid layer as a
power plane and break this plane into smaller islands of
common voltage levels. Keep the metal runs from the
PHASE terminals to the output inductor short. The power
plane should support the input power and output power
nodes. Use copper filled polygons on the top and bottom
circuit layers for the phase nodes. Use the remaining printed
circuit layers for small signal wiring. The wiring traces from
the GATE pins to the MOSFET gates should be kept short
and wide enough to easily handle the 1A of drive current.
In order to dissipate heat generated by the internal V
TT
LDO,
the ground pad, pin 21, should be connected to the internal
ground plane through at least four vias. This allows the heat
to move away from the IC and also ties the pad to the ground
plane through a low impedance path.
The switching components should be placed close to the
ISL6532B first. Minimize the length of the connections
between the input capacitors, C
IN
, and the power switches
by placing them nearby. Position both the ceramic and bulk
input capacitors as close to the upper MOSFET drain as
possible. Position the output inductor and output capacitors
between the upper and lower MOSFETs and the load.
The critical small signal components include any bypass
capacitors, feedback components, and compensation
components. Place the PWM converter compensation
components close to the FB and COMP pins. The feedback
resistors should be located as close as possible to the FB
pin with vias tied straight to the ground plane as required.
Feedback Compensation - PWM Buck Converter
Figure 5 highlights the voltage-mode control loop for a
synchronous-rectified buck converter. The output voltage
(V
OUT
) is regulated to the Reference voltage level. The
error amplifier output (V
E/A
) is compared with the oscillator
(OSC) triangular wave to provide a pulse-width modulated
(PWM) wave with an amplitude of V
IN
at the PHASE node.
The PWM wave is smoothed by the output filter (L
O
and C
O
).
The modulator transfer function is the small-signal transfer
function of V
OUT
/V
E/A
. This function is dominated by a DC
Gain and the output filter (L
O
and C
O
), with a double pole
break frequency at F
LC
and a zero at F
ESR
. The DC Gain of
the modulator is simply the input voltage (V
IN
) divided by the
peak-to-peak oscillator voltage
V
OSC
.
Modulator Break Frequency Equations
V
DDQ
5VSBY
ISLAND ON POWER PLANE LAYER
ISLAND ON CIRCUIT PLANE LAYER
L
OUT
C
OUT1
C
IN
V
IN_DDR
KEY
COMP
ISL6532B
UGATE
R
4
R
2
C
BP
FB
GND
5VSBY
FIGURE 4. PRINTED CIRCUIT BOARD POWER PLANES
AND ISLANDS
R
1
C
2
VIA CONNECTION TO GROUND PLANE
L
Q
1
R
3
C
3
C
1
Q
2
12V
ATX
C
BP
GND
P12V
LGATE
P5VSBY
VDDQ(2)
VTT(2)
C
OUT2
L
V
DDQ
V
TT
NCH
GND PAD
FLC
2
π
x
LO
x
CO
------------------------------------------
=
FESR
ESR
x
CO
------ x
=
ISL6532B
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6532BCR | PWM Control Circuit 16-SSOP 0 to 70 |
| ISL6532BCRZ | PWM Control Circuit 16-SOIC 0 to 70 |
| ISL6532CCRZ-T | R8C Series, 21 Group, WDTO 48P6Q-A |
| ISL6532C | PWM Control Circuit 16-SOIC 0 to 70 |
| ISL6532CCR | PWM Control Circuit 16-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6532BCR | 功能描述:IC REG/CTRLR ACPI DUAL DDR 20QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6532BCR-T | 功能描述:IC REG/CTRLR ACPI DUAL DDR 20QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6532BCRZ | 功能描述:電壓模式 PWM 控制器 DL DDRG W/3ALDO FOR SPRINGDALE MBS 20 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6532BCRZ-T | 功能描述:電壓模式 PWM 控制器 DL DDRG W/3ALDO FOR SPRINGDALE MBS 20 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6532CCR | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。