- 您現在的位置：買賣IC網 > PDF目錄383148 > ISL6444 (Intersil Corporation) Dual PWM Controller with DDR Memory Option for Gateway Applications(帶DDR存儲器選項的網關專用雙PWM控制器) PDF資料下載
參數資料
| 型號： | ISL6444 |
| 廠商： | Intersil Corporation |
| 英文描述： | Dual PWM Controller with DDR Memory Option for Gateway Applications(帶DDR存儲器選項的網關專用雙PWM控制器) |
| 中文描述： | 雙PWM控制器的DDR網關應用（帶的DDR存儲器選項的網關專用雙脈寬調制控制器內存選項） |
| 文件頁數： | 11/19頁 |
| 文件大小： | 372K |
| 代理商： | ISL6444 |
11
FN9069.3
April 12, 2007
Gate Control Logic
The gate control logic translates generated PWM signals
into gate drive signals providing necessary amplification,
level shift, and shoot-trough protection. Also, it bears some
functions that help to optimize the IC performance over a
wide range of the operational conditions. As MOSFET
switching time can very dramatically from type to type and
with the input voltage, the gate control logic provides
adaptive dead time by monitoring real gate waveforms of
both the upper and the lower MOSFETs.
Dual-Step Conversion
The ISL6444 dual channel controller can be used either in
power systems with a single-stage power conversion when
the battery power is converted into the desired output
voltage in one step, or in the systems where some
intermediate voltages are initially established. The choice of
the approach may be dictated by the overall system design
criteria or simply to be a matter of voltages available to the
system designer, like in the case of PCI card applications.
When the power input voltage is a regulated 5V or 3.3V
system bus, the feed-forward ramp may become too
shallow, which creates the possibility of duty-factor jitter
especially in a noisy environment. The noise susceptibility
when operating from low level regulated power sources can
be improved by connecting the VIN pin to ground via a
resistor. The internal pull-up current source of ~15
μ
A will
create a voltage drop across the resistor. If this voltage is
lower than 2.5V, the feed-forward ramp generator will be
internally reconnected from the VIN pin to the VCC pin and
the ramp slew rate will be doubled. Application circuits for
dual-step power conversion are presented in Figure 10.
Protections
The converter output is monitored and protected against
extreme overload, short circuit, overvoltage, and
undervoltage conditions.
A sustained overload on the output sets the PGOOD low and
latches-off the whole chip. The controller operation can be
restored by cycling the VCC voltage or an enable (EN) pin.
Overcurrent Protection
Both PWM controllers use the lower MOSFET’s
on-resistance -- r
DS(ON)
to monitor the current for
protection against shorted outputs. The sensed current
from the ISEN pin is compared with a current set by a
resistor connected from the OCSET pin to ground.
11.2V
R
OC
DS ON
)
Where, I
OC
is a desired overcurrent protection threshold and
R
CS
is the value of the current sense resistor connected to
the I
SEN
pin.
If the lower MOSFET current exceeds the overcurrent
threshold, a pulse skipping circuit is activated. The upper
MOSFET will not be turned on as long as the sensed
current is higher then the threshold value. This limits the
current supplied by the DC voltage source. This condition
keeps on for eight clock cycles after the overcurrent
comparator was tripped for the first time. If after these first
eight clock cycles, the current exceeds the overcurrent
threshold again in a time interval of another eight clock
cycles, the overcurrent protection latches and disables the
chip. If the overcurrent condition goes away during the first
eight clock cycles, normal operation is restored and the
overcurrent circuit resets itself sixteen clock cycles after the
overcurrent threshold was exceeded the first time, Figure 6.
If load step is strong enough to pull output voltage lower
than the undervoltage threshold, the chip shuts down
immediately.
Because of the nature of the used current sensing
technique, and to accommodate wide range of the r
DS(ON)
variation, the value of the overcurrent threshold should
represent overload current about 150%...180% of the
nominal value. If accurate current protection is desired, a
current sense resistor placed in series with the lower
MOSFET source may be used.
Overvoltage Protection
Should the output voltage increase over 115% of the normal
value due to the upper MOSFET failure, or other reasons,
the overvoltage protection comparator will force the
synchronous rectifier gate driver high. This action actively
pulls down the output voltage and eventually attempts to
blow the battery fuse. As soon as the output voltage drops
below the threshold, the OVP comparator is disengaged.
This OVP scheme provides a ‘soft’ crowbar function which
helps to tackle severe load transients and does not invert the
output voltage when activated -- a common problem for OVP
schemes with a latch.
R
OCSET
100
Ω
+
(
)
-----------------------------------------------------------
=
FIGURE 6. OVERCURRENT PROTECTION WAVEFORMS
3
1
2
SHUTDOWN
IL
VOUT
Ch3 1.0A
Ω
Ch2 100mV
M 10.0
μ
s
Ch1 5.0V
PGOOD
8 CLK
ISL6444
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6445 | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6445IAZ | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6445IAZ-TK | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6455 | Triple Output Regulator with Single Synchronous Buck and Dual LDO(帶單同步降壓和雙LDO的三路輸出調節器) |
| ISL6455A | Triple Output Regulator with Single Synchronous Buck and Dual LDO(帶單同步降壓和雙LDO的三路輸出調節器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6444CA | 功能描述:電流型 PWM 控制器 Dual with DDR Memory RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6444CA-T | 功能描述:IC CONTROLLER DDR 28-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6444CAZ | 功能描述:IC CONTROLLER DDR 28-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6444CAZT | 制造商:Intersil Corporation 功能描述: |
| ISL6444CAZ-T | 功能描述:IC CONTROLLER DDR 28-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。