- 您現在的位置：買賣IC網 > PDF目錄383147 > ISL6420IRZ (INTERSIL CORP) Advanced Single Synchronous Buck Pulse-Width Modulation (PWM) Controller PDF資料下載
參數資料
| 型號： | ISL6420IRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Advanced Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| 中文描述： | 0.7 A SWITCHING CONTROLLER, 1400 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 4 X 4 MM, ROHS COMPLIANT, PLASTIC, MO-220-VGGD, QFN-20 |
| 文件頁數： | 16/19頁 |
| 文件大?。?/td> | 525K |
| 代理商： | ISL6420IRZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁
16
FN9151.4
July 18, 2005
The compensation gain uses external impedance networks
Z
FB
and Z
IN
to provide a stable, high bandwidth (BW) overall
loop. A stable control loop has a gain crossing with -
20dB/decade slope and a phase margin greater than 45°.
Include worst case component variations when determining
phase margin.
Component Selection Guidelines
Output Capacitor Selection
An output capacitor is required to filter the output and supply
the load transient current. The filtering requirements are a
function of the switching frequency and the ripple current.
The load transient requirements are a function of the slew
rate (di/dt) and the magnitude of the transient load current.
These requirements are generally met with a mix of
capacitors and careful layout.
Modern microprocessors produce transient load rates above
1A/ns. High frequency capacitors initially supply the transient
and slow the current load rate seen by the bulk capacitors.
The bulk filter capacitor values are generally determined by
the ESR (effective series resistance) and voltage rating
requirements rather than actual capacitance requirements.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load on
specific decoupling requirements. For example, Intel
recommends that the high frequency decoupling for the
Pentium Pro be composed of at least forty (40) 1.0μF
ceramic capacitors in the 1206 surface-mount package.
Use only specialized low-ESR capacitors intended for
switching-regulator applications for the bulk capacitors.
The bulk capacitor’s ESR will determine the output ripple
voltage and the initial voltage drop after a high slew-rate
transient. An aluminum electrolytic capacitor's ESR value is
related to the case size with lower ESR available in larger
case sizes. However, the equivalent series inductance (ESL)
of these capacitors increases with case size and can reduce
the usefulness of the capacitor to high slew-rate transient
loading. Unfortunately, ESL is not a specified parameter.
Work with your capacitor supplier and measure the
capacitor’s impedance with frequency to select a suitable
component. In most cases, multiple electrolytic capacitors of
small case size perform better than a single large case
capacitor.
Output Inductor Selection
The output inductor is selected to meet the output voltage
ripple requirements and minimize the converter’s response
time to the load transients. The inductor value determines
the converter’s ripple current and the ripple voltage is a
function of the ripple current and the output capacitors ESR.
The ripple voltage and current are approximated by the
following equations:
Increasing the value of inductance reduces the ripple current
and voltage. However, larger inductance values reduce the
converter’s response time to a load transient.
One of the parameters limiting the converter’s response to a
load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL6420 will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
required to slew the inductor current from an initial current
value to the transient current level. During this interval the
difference between the inductor current and the transient
current level must be supplied by the output capacitor.
Minimizing the response time can minimize the output
capacitance required.
The response time to a transient is different for the
application of load and the removal of load. The following
equations give the approximate response time interval for
application and removal of a transient load:
where: I
TRAN
is the transient load current step, t
RISE
is the
response time to the application of load, and t
FALL
is the
response time to the removal of load. With a +5V input
source, the worst case response time can be either at the
application or removal of load and dependent upon the
output voltage setting. Be sure to check both of these
100
80
60
40
20
0
-20
-40
-60
F
P1
F
Z2
10M
1M
100K
10K
1K
100
10
OPEN LOOP
ERROR AMP GAIN
F
Z1
F
P2
F
LC
F
ESR
COMPENSATION
GAIN
G
FREQUENCY (Hz)
20LOG
(V
IN
/
V
OSC
)
MODULATOR
GAIN
20LOG
(R2/R1)
CLOSED LOOP
GAIN
FIGURE 15. ASYMPTOTIC BODE PLOT OF CONVERTER GAIN
I
L
V
- V
Fs x L
-------------------------------
V
V
IN
---------------
=
(EQ. 10)
V
OUT
I
L
ESR
=
(EQ. 11)
t
RISE
L
V
IN
V
OUT
–
-------------------------------
=
(EQ. 12)
t
FALL
L
------------------------------
I
OUT
×
=
(EQ. 13)
ISL6420
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6420IRZ-TK | Advanced Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6420 | Quadruple 2-Input Positive-AND Gates 14-SOIC -40 to 85 |
| ISL6420IA | Quadruple 2-Input Positive-AND Gates 14-SSOP -40 to 85 |
| ISL6420IR | Quadruple 2-Input Positive-AND Gates 14-SSOP -40 to 85 |
| ISL6420IR-T | Advanced Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6420IRZS2698 | 制造商:Intersil Corporation 功能描述:PB-FREE SYNC BUCK PWM CONT. WITH 4.5V-16V INPUT,20LD 4X4 QFN - Rail/Tube |
| ISL6420IRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6420IRZ-TK | 功能描述:IC REG CTRLR BUCK PWM VM 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6420IRZ-TKR5207 | 制造商:Intersil Corporation 功能描述: |
| ISL6420IRZ-TKS2698 | 制造商:Intersil Corporation 功能描述:PB-FREE SYNCH BUCK PWM CONT. WITH 4.5V-16V INPUT,20LD 4X4 QF - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。