參數資料
型號： ISL6420IRZ
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： Advanced Single Synchronous Buck Pulse-Width Modulation (PWM) Controller
中文描述： 0.7 A SWITCHING CONTROLLER, 1400 kHz SWITCHING FREQ-MAX, PQCC20
封裝： 4 X 4 MM, ROHS COMPLIANT, PLASTIC, MO-220-VGGD, QFN-20
文件頁數： 14/19頁
文件大?。?/td> 525K
代理商： ISL6420IRZ
14
FN9151.4
July 18, 2005
Over-Temperature Protection
The IC is protected against overtemperature conditions.
When the junction temperature exceeds 150°C, the PWM
shuts off. Normal operation is resumed when the junction
temperature is cooled down to 130°C.
Shutdown
When ENSS pin is below 1V, the regulator is disabled with
the PWM output drivers three-stated. When disabled, the IC
power will be reduced.
Under-Voltage
If the voltage on the FB pin is less than 15% of the reference
voltage for 8 consecutive PWM cycles, then the circuit enters
into soft-start hiccup mode. This mode is identical to the
overcurrent hiccup mode.
Overvoltage Protection
If the voltage on the FB pin exceeds the reference voltage by
15%, the lower gate driver is turned on continuously to
discharge the output voltage. If the overvoltage condition
continues for 32 consecutive PWM cycles, then the chip is
turned off with the gate drivers three-stated. The voltage on
the FB pin will fall and reach the 15% undervoltage
threshold. After 8 clock cycles, the chip will enter soft-start
hiccup mode. This mode is identical to the overcurrent
hiccup mode.
Gate Control Logic
The gate control logic translates generated PWM control
signals into the MOSFET gate drive signals providing
necessary amplification, level shifting and shoot-through
protection. Also, it has functions that help optimize the IC
performance over a wide range of operational conditions.
Since MOSFET switching time can vary dramatically from
type to type and with the input voltage, the gate control logic
provides adaptive dead time by monitoring the gate-to-
source voltages of both upper and lower MOSFETs. The
lower MOSFET is not turned on until the gate-to-source
voltage of the upper MOSFET has decreased to less than
approximately 1V. Similarly, the upper MOSFET is not turned
on until the gate-to-source voltage of the lower MOSFET has
decreased to less than approximately 1V. This allows a wide
variety of upper and lower MOSFETs to be used without a
concern for simultaneous conduction, or shoot-through.
Application Guidelines
Layout Considerations
As in any high frequency switching converter, layout is very
important. Switching current from one power device to
another can generate voltage transients across the
impedances of the interconnecting bond wires and circuit
traces. These interconnecting impedances should be
minimized by using wide, short printed circuit traces. The
critical components should be located as close together as
possible using ground plane construction or single point
grounding.
Figure 12 shows the critical power components of the
converter. To minimize the voltage overshoot the
interconnecting wires indicated by heavy lines should be part
of ground or power plane in a printed circuit board. The
components shown in Figure 12 should be located as close
together as possible. Please note that the capacitors C
IN
and C
O
each represent numerous physical capacitors.
Locate the ISL6420 within 3 inches of the MOSFETs, Q1 and
Q2. The circuit traces for the MOSFETs’ gate and source
connections from the ISL6420 must be sized to handle up to
2A peak current.
Figure 13
shows the circuit traces that require additional
layout consideration. Use single point and ground plane
construction for the circuits shown. Minimize any leakage
current paths on the SS PIN and locate the capacitor, C
ss
close to the SS pin because the internal current source is
only 30μA. Provide local V
CC
decoupling between VCC and
GND pins. Locate the capacitor, C
BOOT
as close as practical
to the BOOT and PHASE pins.
GND
L
O
C
O
LGATE
UGATE
PHASE
Q1
Q2
D2
FIGURE 12. PRINTED CIRCUIT BOARD POWER AND
GROUND PLANES OR ISLANDS
V
IN
V
OUT
RETURN
ISL6420
C
IN
L
FIGURE 13. PRINTED CIRCUIT BOARD SMALL SIGNAL
LAYOUT GUIDELINES
+5V
ISL6420
SS/EN
GND
VCC
BOOT
D1
L
O
C
O
V
OUT
L
Q1
Q2
PHASE
+V
IN
C
BOOT
C
VCC
C
SS
ISL6420
相關PDF資料
PDF描述
ISL6420IRZ-TK Advanced Single Synchronous Buck Pulse-Width Modulation (PWM) Controller
ISL6420 Quadruple 2-Input Positive-AND Gates 14-SOIC -40 to 85
ISL6420IA Quadruple 2-Input Positive-AND Gates 14-SSOP -40 to 85
ISL6420IR Quadruple 2-Input Positive-AND Gates 14-SSOP -40 to 85
ISL6420IR-T Advanced Single Synchronous Buck Pulse-Width Modulation (PWM) Controller
相關代理商/技術參數
參數描述
ISL6420IRZS2698 制造商:Intersil Corporation 功能描述:PB-FREE SYNC BUCK PWM CONT. WITH 4.5V-16V INPUT,20LD 4X4 QFN - Rail/Tube
ISL6420IRZ-T 功能描述:IC REG CTRLR BUCK PWM VM 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6420IRZ-TK 功能描述:IC REG CTRLR BUCK PWM VM 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6420IRZ-TKR5207 制造商:Intersil Corporation 功能描述:
ISL6420IRZ-TKS2698 制造商:Intersil Corporation 功能描述:PB-FREE SYNCH BUCK PWM CONT. WITH 4.5V-16V INPUT,20LD 4X4 QF - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*