- 您現在的位置：買賣IC網 > PDF目錄383146 > ISL6413 (Intersil Corporation) Hex Inverters 14-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6413 |
| 廠商： | Intersil Corporation |
| 英文描述： | Hex Inverters 14-SOIC -40 to 85 |
| 中文描述： | 三單和雙同步降壓穩壓器LDO輸出 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 380K |
| 代理商： | ISL6413 |
8
Pin Descriptions
PVCC
- Positive supply for the power (internal FET) stage of
the PWM section.
SGND
- Analog ground for the PWM. All internal control
circuits are referenced to this pin.
EN
_
PWM
- The PWM controller is enabled when this pin is
HIGH, and held off when the pin is pulled LOW. It is a CMOS
logic-level input (referenced to V
IN
).
V
IN
_LDO
- This is the input voltage pin for LDO1 and LDO2.
EN_LDO
- LDO1 and LDO2 are enabled when this pin is
HIGH, and held off when the pin is pulled LOW. It is a CMOS
logic-level input (referenced to V
IN
).
CT
- Timing capacitor connection to set the 25ms minimum
pulse width for the RESET/RESET signal.
RESET, RESET
- These complementary pins are the
outputs of the reset supervisory circuit, which monitors V
IN
.
The IC asserts these RESET and RESET signals whenever
the supply voltage drops below a preset threshold; keeping
them asserted for at least 25ms after V
CC
(V
IN
) has risen
above the reset threshold. These outputs are push-pull.
RESET is LOW when re-setting the microprocessor. The
device will continue to operate until V
IN
drops below the
UVLO threshold.
PG_LDO
- This is a high impedance open drain output that
provides the status of both LDOs. When either of the outputs
are out of regulation, PG_LDO goes LOW.
CC1
- This is the compensation capacitor connection for
LDO1. Connect a 0.033μF capacitor from CC1 to
GND_LDO.
CC2
- This is the compensation capacitor connection for
LDO2. Connect a 0.033μF capacitor from CC2 to
GND_LDO.
V
OUT2
- This pin is the output of LDO2. Bypass with a 2.2μF,
low ESR capacitor to GND_LDO for stable operation.
GND_LDO
- Ground pin for LDO1 and LDO2.
V
OUT1
- This pin is the output of LDO1. Bypass with a 2.2μF,
low ESR capacitor to GND_LDO for stable operation.
PGND
- Power ground for the PWM controller stage.
V
OUT
- This I/O pin senses the output voltage of the PWM
converter stage. For fixed 1.8V operation, connect this pin
directly to the output voltage.
PG_PWM
- This pin is an active pull-up/pull-down able to
source/sink 1mA (min.) at 0.4V from V
IN
/SGND. This output
is HIGH when V
OUT
is within ±8% (typ.).
PG_PWM
- This pin provides an inverted PG_PWM output.
LX
- The LX pin is the switching node of synchronous buck
converter, connected internally at the junction point of the
upper MOSFET source and lower MOSFET drain. Connect
this pin to the output inductor.
V
IN
- This pin is the power supply for the PWM controller
stage and must be closely decoupled to ground.
SYNC
- This is the external clock synchronization input. The
device can be synchronized to 500kHz to 1MHz switching
frequency.
GND
- Tie this pin to the ground plane with a low impedance,
shortest possible path.
Functional Description
The ISL6413 is a 3-in-1 multi-output regulator designed for
wireless chipset power applications. The device integrates a
single synchronous buck regulator with dual LDOs. It
supplies three fixed output voltages 1.8V, 2.84V and 2.84V.
The 1.8V is generated using a synchronous buck regulator
with greater then 92% efficiency. Both 2.84V supplies are
generated from ultra low noise LDO Regulators. Under
voltage lock-out (UVLO) prevents the converter from turning
on when the input voltage is less then typically 2.6V
Additional blocks include an output over-current protections,
thermal sensor, PGOOD detectors, RESET function and
shutdown logic.
Synchronous Buck Regulator
The Synchronous buck regulator with integrated N- and
P-channel power MOSFET provides pre-set 1.8V for
BBP/MAC core supply. Synchronous rectification with
internal MOSFETs is used to achieve higher efficiency and
reduced number of external components. Operating
frequency is typically 750kHz allowing the use of smaller
inductor and capacitor values. The device can be
synchronized to an external clock signal in the range of
500kHz to 1MHz. The PG_PWM output indicates loss of
regulation on PWM output.
The PWM architecture uses a peak current mode control
scheme with internal slope compensation. At the beginning
of each clock cycle, the high side P-channel MOSFET is
turned on. The current in the inductor ramps up and is
sensed via an internal circuit. The error amplifier sets the
threshold for the PWM comparator. The high side switch is
turned off when the sensed inductor current reaches this
threshold. After a minimum dead time preventing shoot
through current, the low side N-channel MOSFET will be
turned on and the current ramps down again. As the clock
cycle is completed, the low side switch will be turned off and
the next clock cycle starts.
The control loop is internally compensated reducing the
amount of external components. The PWM section includes
an anti-ringing switch to reduce noise at light loads.
The switch current is internally sensed and the minimum
current limit is 600mA.
ISL6413
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6413IR | Triple Output Regulator with Single Synchronous Buck and Dual LDO |
| ISL6414 | Hex Inverters 14-PDIP -40 to 85 |
| ISL6414IR-T5K | Triple Output, Low-Noise LDO Regulator with Integrated Reset Circuit |
| ISL6414IR-TK | Triple Output, Low-Noise LDO Regulator with Integrated Reset Circuit |
| ISL6414IR | Hex Inverters 14-PDIP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6413EVAL1 | 功能描述:EVALUATION BOARD ISL6413 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6413IR | 功能描述:IC REG TRPL BCK/LINEAR 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6413IR-T5K | 功能描述:IC REG TRPL BCK/LINEAR 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6413IR-TK | 功能描述:IC REG TRPL BCK/LINEAR 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6413IRZ | 功能描述:IC REG TRPL BCK/LINEAR 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。