- 您現在的位置：買賣IC網 > PDF目錄383146 > ISL6413 (Intersil Corporation) Hex Inverters 14-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6413 |
| 廠商： | Intersil Corporation |
| 英文描述： | Hex Inverters 14-SOIC -40 to 85 |
| 中文描述： | 三單和雙同步降壓穩壓器LDO輸出 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 380K |
| 代理商： | ISL6413 |
10
voltage, the integrator capacitor voltage is raised or lowered
to compensate for the systematic offset at the error amplifier.
Compensation is limited to ±5% to minimize transient
overshoot when the device goes out of dropout, current limit,
or thermal shutdown.
Shutdown
Driving the EN_LDO pin low will put LDO1 and LDO2 into
the shutdown mode. Driving the EN_PWM pin low will put
the PWM into shutdown mode. Pulling the EN_PWM and
EN_LDO both pins low simultaneously, puts the complete
chip into shutdown mode, and supply current drops to 15μA
typical.
Protection Features for the LDOs
Current Limit
The ISL6413 monitors and controls the pass transistor’s
gate voltage to limit the output current. The current limit for
LDO1 is 330mA and LDO2 is 250mA. The output can be
shorted to ground without damaging the part due to the
current limit and thermal protection features.
Thermal Overload Protection
Thermal overload protection limits total power dissipation in
the ISL6413. When the junction temperature (T
J
) exceeds
+150°C, the thermal sensor sends a signal to the shutdown
logic, turning off the pass transistor and allowing the IC to
cool. The pass transistor turns on again after the IC’s
junction temperature typically cools by 20°C, resulting in a
pulsed output during continuous thermal overload
conditions. Thermal overload protection protects the
ISL6413 against fault conditions. For continuous operation,
do not exceed the absolute maximum junction temperature
rating of +150°C.
Operating Region and Power Dissipation
The maximum power dissipation of ISL6413 depends on the
thermal resistance of the IC package and circuit board, the
temperature difference between the die junction and ambient
air, and the rate of air flow. The power dissipated in the
device is:
PT = P1 + P2 + P3, where
P1 = I
OUT1
x V
OUT1
/I
IN
x V
IN
P2 = I
OUT2
(V
IN
– V
OUT2
)
P3 = I
OUT3
(V
IN
- V
OUT3
)
The maximum power dissipation is:
Pmax = (Tjmax – T
A
)/
θ
JA
Where Tjmax = 150
o
C, T
A
= ambient temperature, and
θ
JA
is the thermal resistance from the junction to the surrounding
environment.
The ISL6413 package features an exposed thermal pad on
its underside. This pad lowers the thermal resistance of the
package by providing a direct heat conduction path from the
die to the PC board. Additionally, the ISL6413’s ground
(GND_LDO and PGND) performs the dual function of
providing an electrical connection to system ground and
channeling heat away. Connect the exposed backside pad
direct to the GND_LDO ground plane.
Applications Information
LDO Regulator Capacitor Selection and Regulator
Stability
Capacitors are required at the ISL6413 LDO Regulators’
input and output for stable operation over the entire load
range and the full temperature range. Use >1μF capacitor at
the input of LDO Regulators, V
IN
_LDO pins. The input
capacitor lowers the source impedance of the input supply.
Larger capacitor values and lower ESR provides better
PSRR and line transient response. The input capacitor must
be located at a distance of not more then 0.5 inches from the
V
IN
pins of the IC and returned to a clean analog ground.
Any good quality ceramic capacitor can be used as an input
capacitor.
The output capacitor must meet the requirements of
minimum amount of capacitance and ESR for both LDO’s.
The ISL6413 is specifically designed to work with small
ceramic output capacitors. The output capacitor’s ESR
affects stability and output noise. Use an output capacitor
with an ESR of 50m
or less to insure stability and optimum
transient response. For stable operation, a ceramic
capacitor, with a minimum value of 3.3μF, is recommended
for V
OUT1
for 300mA output current, and 3.3μF is
recommended for V
OUT2
at 200mA load current. There is no
upper limit to the output capacitor value. Larger capacitor
can reduce noise and improve load transient response,
stability and PSRR. Higher value of output capacitor (10μF)
is recommended for LDO2 when used to power VCO
circuitry in wireless chipsets. The output capacitor should be
located very close to V
OUT
pins to minimize impact of PC
board inductances and the other end of the capacitor should
be returned to a clean analog ground.
PWM Regulator Component Selection
INDUCTOR SELECTION
A 10μH minimum output inductor is used with the ISL6413
PWM section. Values larger then 15μH or less then 10μH
may cause stability problems because of the internal
compensation of the regulator. The important parameters of
the inductor that need to be considered are the current rating
of the inductor and the DC resistance of the inductor. The dc
resistance of the inductor will influence directly the efficiency
of the converter. Therefore, an inductor with lowest dc
resistance should be selected for highest efficiency.
ISL6413
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6413IR | Triple Output Regulator with Single Synchronous Buck and Dual LDO |
| ISL6414 | Hex Inverters 14-PDIP -40 to 85 |
| ISL6414IR-T5K | Triple Output, Low-Noise LDO Regulator with Integrated Reset Circuit |
| ISL6414IR-TK | Triple Output, Low-Noise LDO Regulator with Integrated Reset Circuit |
| ISL6414IR | Hex Inverters 14-PDIP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6413EVAL1 | 功能描述:EVALUATION BOARD ISL6413 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6413IR | 功能描述:IC REG TRPL BCK/LINEAR 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6413IR-T5K | 功能描述:IC REG TRPL BCK/LINEAR 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6413IR-TK | 功能描述:IC REG TRPL BCK/LINEAR 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL6413IRZ | 功能描述:IC REG TRPL BCK/LINEAR 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。