- 您現在的位置：買賣IC網 > PDF目錄384522 > ISL5585GCRZ (INTERSIL CORP) 3.3V Ringing SLIC Family for Voice Over Broadband (VOB) PDF資料下載
參數資料
| 型號： | ISL5585GCRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 模擬傳輸電路 |
| 英文描述： | 3.3V Ringing SLIC Family for Voice Over Broadband (VOB) |
| 中文描述： | TELECOM-SLIC, PQCC32 |
| 封裝： | 7 X 7 MM, LEAD FREE, PLASTIC, MO-220VKKC, QFN-32 |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 455K |
| 代理商： | ISL5585GCRZ |
10
detection of ring trip or programmed off hook loop current,
whichever is greater.
To allow for proper ring trip operation, the transient current
limit setting should be set at least 25% higher than the peak
ring trip current setting. Setting the transient current 25%
higher should account for programming tolerances of both
the ring trip threshold and the transient current limit.
If loop current is larger than ring trip current (low REN
applications) then the transient current limit should be set at
least 35% higher than the loop current setting. The slightly
higher offset accounts for the slope of the loop current limit
function.
Attention to detail should be exercised when programming
the transient current limit setting. If ring trip detect does not
occur while ringing, then re-examine the transient current
limit and ring trip threshold settings.
DC Loop Feed
The feedback mechanism for monitoring the DC portion of
the loop current is the loop detector. A low pass filter is used
in the feedback to block voice band signals from interfering
with the loop current limit function. The pole of the low pass
filter is set by the external capacitor C
DC
. The value of the
external capacitor should be 4.7
μ
F, 6.3V rated polarized or
non-polarized capacitor.
Most applications will operate the device from low battery
while off hook. The DC feed characteristic of the device will
drive Tip and Ring towards half battery to regulate the DC
loop current. For light loads or Long Loops, Tip will be near
-4V and Ring will be near V
VBL
+ 5V. Figure 2 shows the DC
feed characteristic in terms of tip to ring voltage and loop
current.
The point on the y-axis labeled V
TR(OC)
is the open circuit
Tip to Ring voltage and is defined by the feed battery voltage
in Equation 6.
Figure 3 illustrates the actual loop current for a given set of
loop conditions. The loop conditions are determined by the
low battery voltage and the DC loop impedance. The DC
loop impedance is the sum of the protection resistance,
copper resistance (ohms/foot) and the telephone off hook
DC resistance.
The slope of the feed characteristic and the battery voltage
define the maximum loop current on the shortest possible
loop as the short circuit current I
SC
.
V
The term I
LIM
is the programmed current limit, 1760/R
IL
. The
line segment I
A
represents the constant current region of the
loop current limit function.
Process variations in the ISL5585 effect the I
LIM
and
11.11k
slope in Equation 8. All units are tested with: a
300
load across tip and ring, V
BAT
=-24V and I
LIM
set to
25mA. Equation 8 can be used to predict the ideal current at
this setting (25.76mA). All units are tested to be within
±8.5% of this ideal value (23.57mA to 27.95mA).
The maximum loop impedance for a programmed loop
current is defined as R
KNEE
.
V
)
LIM
When R
KNEE
is exceeded, the device will transition from
constant current feed to constant voltage or resistive feed.
The line segment I
B
represents the resistive feed portion of
the load characteristic
V
(
)
LOOP
Impedance Matching
The impedance of the device is programmed with the
external component R
S
. R
S
is the gain setting resistor for
the Transmit Amplifier that provides impedance matching. If
complex impedance matching is required, then a complex
network can be substituted for R
S
.
The feedback mechanism for monitoring the AC portion of
the loop current consists of two amplifiers, the Sense
Amplifier (SA) and the Transmit Amplifier (TA). The AC
feedback signal is used for impedance synthesis. A detailed
model of the AC feed back loop is shown in Figure 4.
FIGURE 2. DC FEED CHARACTERISTIC
m = (
V
TR
/
I
L
) = 11.1k
I
LOOP
(mA)
I
LIM
V
TR(OC)
V
T
,
LONG LOOP
SHORT LOOP
V
TR OC
(
)
V
BL
9
–
=
(EQ. 6)
FIGURE 3. I
LOOP
vs. R
LOOP
LOAD CHARACTERISTIC
R
LOOP
(
)
R
KNEE
I
LIM
I
L
I
SC
I
A
I
B
m=Vtr(oc)/Rloop
2R
P
LONG LOOP
SHORT LOOP
m=11.11k
CONSTANT CURRENT
CONSTANT VOLTAGE
OR
RESISTIVE FEED
I
SC
I
LIM
2R
I
–
-----------------------------------------------------
+
=
(EQ. 7)
I
A
I
LIM
V
--------------------------------------------------------------
R
I
–
+
=
(EQ. 8)
R
KNEE
-----------------------
=
(EQ. 9)
I
B
-----------------------
=
(EQ. 10)
ISL5585
相關PDF資料 |
PDF描述 |
|---|---|
| ISL5586 | Low Power Ringing SLIC for Home Gateways(家用網關的低功耗振鈴芯片) |
| ISL5627 | Dual 8-bit, +3.3V, 260+MSPS, High Speed D/A Converter |
| ISL5627EVAL1 | Dual 8-bit, +3.3V, 260+MSPS, High Speed D/A Converter |
| ISL5627IN | Dual 8-bit, +3.3V, 260+MSPS, High Speed D/A Converter |
| ISL5640 | Dual 8-Bit, A/D Converter with Internal Voltage Reference(雙路8位帶內部電壓基準的A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL5585GCRZ-T | 制造商:Intersil Corporation 功能描述:PB-FREE RINGING SLIC W/3.3V VCC, 100V/53DB, T&R - Tape and Reel |
| ISL5585GCRZ-TK | 制造商:Intersil Corporation 功能描述:SLIC 1CH 53DB 45MA 3.3V/-18V/-24V/-28V 32QFN EP - Tape and Reel |
| ISL5585XEVAL1 | 功能描述:EVALUATION BOARD FOR ISL5585 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL5586 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power Ringing SLIC for Home Gateways |
| ISL5586_04 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power Ringing SLIC for Home Gateways |
發布緊急采購，3分鐘左右您將得到回復。