參數資料
型號: ISL5585ECRZ-TK
廠商: Intersil
文件頁數: 11/24頁
文件大?。?/td> 0K
描述: IC SLIC RINGING 3.3V VOB 32-QFN
標準包裝: 1,000
功能: 用戶線路接口概念(SLIC)
電路數: 1
電源電壓: 3.3V
功率(瓦特): 305mW
工作溫度: 0°C ~ 75°C
安裝類型: 表面貼裝
封裝/外殼: 32-VQFN 裸露焊盤
供應商設備封裝: 32-QFN(7x7)
包裝: 帶卷 (TR)
包括: 均衡和不均衡振鈴,振鈴聲信號發生器,熱關機,帶警報指示器
19
When the forward loop back mode is initiated internal
switches connect a 600
load across the outputs of the Tip
and Ring amplifiers.
DC Verification
When the internal signal path is provided, DC current will
flow from Tip to Ring. The DC current will force DET low,
indicating the presence of loop current. In addition, the ALM
output will also go low. This does not indicate a thermal
alarm condition. Rather, proper logic operation is verified in
the event of a thermal shutdown. In addition to verifying
device functionality, toggling the logic outputs verifies the
interface to the system controller.
AC Verification
The entire AC loop of the device is active during the forward
loop back mode. Therefore a 4-wire to 4-wire level test
capability is provided. Depending on the transhybrid balance
implementation, test coverage is provided by a one or two
step process.
System architectures which cannot disable the transhybrid
function would require a two step process. The first step
would be to send a test tone to the device while on hook and
not in forward loop back mode. The return signal would be
the test level times the gain RF/RA of the transhybrid
amplifier. Since the device would not be terminated,
cancellation would not occur. The second step would be to
program the device to FLB and resend the test tone. The
return signal would be much lower in amplitude than the first
step, indicating the device was active and the internal
termination attenuated the return signal. System
architectures which disable the transhybrid function would
achieve test coverage with a signal step. Once the
transhybrid function is disable, program the device for FLB
and send the test tone. The return signal level is determined
by the 4-wire to 4-wire gain of the device.
Tip Open
Overview
The tip open mode (110) is intended for compatibility for PBX
type interfaces. Used during idle line conditions, the device
does not provide transmission. Loop supervision is provided
by either the switch hook detector (E0 = 1) or the ground key
detector (E0 = 0). The ground key detector will be used in
most applications. The device may be operated from either
high or low battery.
Functionality
During tip open operation, the Tip switch is disabled and the
Ring switch is enabled. The minimum Tip impedance is
30k
. The only active path through the device will be the
Ring switch.
In keeping with the MTU characteristics of the device, Ring
will not exceed -56V when operating from the high battery.
Though MTU does not apply to tip open, safety requirements
are satisfied.
FIGURE 13. FORWARD LOOP BACK INTERNAL TERMINATION
RING AMP
TIP AMP
RING
TIP
600
ISL5585
相關PDF資料
PDF描述
ISL5585FCRZ-TK IC SLIC RINGING 3.3V VOB 32-QFN
IDT82P2821BHG IC LINE INTERFACE UNIT 640-PBGA
SI3062-F-FS IC DAA ENH FCC LINE-SIDE 16SOIC
VE-26N-IX-S CONVERTER MOD DC/DC 18.5V 75W
S9S08SG32E1WTLR IC MCU 8BIT 32KB FLASH 28TSSOP
相關代理商/技術參數
參數描述
ISL5585EVAL4 制造商:Intersil Corporation 功能描述:ISL5585 EVALUATION BOARD 4 - Bulk
ISL5585FCM 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述:
ISL5585FCMZ 制造商:Intersil Corporation 功能描述:SLIC 1CH 53DB 45MA 3.3V/-18V/-24V/-28V 28PLCC - Rail/Tube 制造商:Intersil 功能描述:RINGING SLIC W/3 3V VCC 75V/53DB
ISL5585FCMZ-T 制造商:Intersil Corporation 功能描述:SLIC 1CH 53DB 45MA 3.3V/-18V/-24V/-28V 28PLCC - Tape and Reel 制造商:Intersil 功能描述:RINGING SLIC W/3 3V VCC 75V/53DB
ISL5585FCR 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:3.3V Ringing SLIC Family for Voice Over Broadband VOB