- 您現在的位置：買賣IC網 > PDF目錄384519 > ISL22446 (Intersil Corporation) Low Noise, Low Power, SPI Bus, 128 Taps(低噪聲,低功率，SPI總線, 128抽頭電位器) PDF資料下載
參數資料
| 型號： | ISL22446 |
| 廠商： | Intersil Corporation |
| 英文描述： | Low Noise, Low Power, SPI Bus, 128 Taps(低噪聲,低功率，SPI總線, 128抽頭電位器) |
| 中文描述： | 低噪聲，低功耗，SPI總線，128絲錐（低噪聲，低功率和SPI總線，128抽頭電位器） |
| 文件頁數： | 11/13頁 |
| 文件大?。?/td> | 465K |
| 代理商： | ISL22446 |
11
FN6181.0
July 17, 2006
Protocol Conventions
The first byte sent to the ISL22446 from the SPI host is the
Identification Byte. A valid Identification Byte contains 0101
as the four MSBs, with the following four bits set to 0.
TABLE 3. IDENTIFICATION BYTE FORMAT
The next byte sent to the ISL22446 contains the instruction
and register pointer information. The four MSBs are the
instruction and four LSBs are register address (see Table 4).
TABLE 4. IDENTIFICATION BYTE FORMAT
There are only two valid instruction sets:
1011(binary) - is a Read operation
1100(binary) - is a Write operation
Write Operation
A Write operation to the ISL22446 is a three-byte operation.
It requires first, the CS transition from HIGH to LOW, then a
valid Identification Byte, then a valid instruction byte
following by Data Byte is sent to SDI pin. The host
terminates the write operation by pulling the CS pin from
LOW to HIGH. For a write to addresses 0000b to 0011b, the
MSB at address 8 (ACR[7]) determines if the Data Byte is to
be written to volatile or both volatile and non-volatile
registers. Refer to “Memory Description” and Figure 16.
Device can receive more than one byte of data by auto
incrementing the address after each received byte. Note
after reaching the address 0110b, the internal pointer “rolls
over” to address 0000b.
The internal non-volatile write cycle starts after rising edge of
CS and takes up to 20ms. Thus, non-volatile registers must
be written individually.
Read Operation
A read operation to the ISL22446 is a three-byte operation. It
requires first, the CS transition from HIGH to LOW, then a
valid Identification Byte, then a valid instruction byte
following by “dummy” Data Byte is sent to SDI pin. The SPI
host reads the data from SDO pin on falling edge of SCK.
The host terminates the read operation by pulling the CS pin
from LOW to HIGH (see Figure 17).
The ISL22446 will provide the Data Bytes to the SDO pin as
long as SCK is provided by the host from the registers
indicated by an internal pointer. This pointer initial value is
determined by the register address in the Read operation
instruction, and increments by one during transmission of
each Data Byte. After reaching the memory location 0110b,
the pointer “rolls over” to 0000b, and the device continues to
output the data for each received SCK clock.
In order to read back the non-volatile IVR, it is recommended
that the application reads the ACR first to verify the WIP bit
is 0. If the WIP bit (ACR[5]) is not 0, the host should repeat
its reading sequence again.
FIGURE 16. THREE BYTE WRITE SEQUENCE
FIGURE 17. THREE BYTE READ SEQUENCE
0
1
0
1
0
0
0
0
(MSB)
(LSB)
7
6
5
4
3
2
1
0
I3
I2
I1
I0
R3
R2
R1
R0
0
1
0
1
0
0
I3
I2
I1
I0
R3
R2
R1
R0
SCK
SDI
0
D6
D5 D4
D3
D2
D1 D0
CS
0
0
0
0
1
0
1
0
0
I3
I2
I1
I0
R3
R2
R1 R0
SCK
SDI
CS
0
0
SDO
0
D6
D5 D4
D3
D2
D1 D0
DON’T CARE
0
ISL22446
相關PDF資料 |
PDF描述 |
|---|---|
| ISL22449 | Low Noise, Low Power, SPI Bus, 128 Taps, Wiper Only(低噪聲,低功率，SPI總線, 128抽頭電位器) |
| ISL28156 | 39μA Micropower Single and Dual Precision Rail-to-Rail Input-Output (RRIO) Low Input Bias Current Op Amps(39μA，微功率單/雙精度軌對軌輸入-輸出(RRIO)，低輸入偏流運放) |
| ISL28256 | 39μA Micropower Single and Dual Precision Rail-to-Rail Input-Output (RRIO) Low Input Bias Current Op Amps(39μA，微功率單/雙精度軌對軌輸入-輸出(RRIO)，低輸入偏流運放) |
| ISL37105P-CD | PRISM 3 11 Mbps Wireless Local Area Network PCMCIA |
| ISL37105P-EVAL | PRISM 3 11 Mbps Wireless Local Area Network PCMCIA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22446UFRT20Z | 功能描述:數字電位計 IC 128 TAP FL RNG IND QD DCP 20LD 4X4 TQFN RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22446UFRT20Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG IND QD DCP 20LD 4X4 TQFN RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22446UFV20Z | 功能描述:數字電位計 IC 128 TAP FL RNG IND QD DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22446UFV20Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG IND QD DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22446WFRT20Z | 功能描述:數字電位計 IC 128 TAP FL RNG IND QD DCP 20LD 4X4 TQFN RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。