- 您現在的位置：買賣IC網 > PDF目錄2001 > ISL1221IUZ (Intersil)IC RTC LP BATT BACK SRAM 10MSOP PDF資料下載
參數資料
| 型號： | ISL1221IUZ |
| 廠商： | Intersil |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC LP BATT BACK SRAM 10MSOP |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 980 |
| 類型： | 時間事件記錄器 |
| 特點： | 警報器，閏年，SRAM |
| 存儲容量： | 2B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
19
FN6316.1
July 15, 2010
Device Addressing
Following a start condition, the master must output a Slave
Address Byte. The 7 MSBs are the device identifier. These
bits are “1101111”. Slave bits “1101” access the register.
Slave bits “111” specify the device select bits.
The last bit of the Slave Address Byte defines a read or write
operation to be performed. When this R/W bit is a “1”, then a
read operation is selected. A “0” selects a write operation
(Refer to Figure 17).
After loading the entire Slave Address Byte from the SDA
bus, the ISL1221 compares the device identifier and device
select bits with “1101111”. Upon a correct compare, the
device outputs an acknowledge on the SDA line.
Following the Slave Byte is a one byte word address. The
word address is either supplied by the master device or
obtained from an internal counter. On power up the internal
address counter is set to address 0h, so a current address
read of the CCR array starts at address 0h. When required,
as part of a random read, the master must supply the 1 Word
Address Bytes as shown in Figure 18.
In a random read operation, the slave byte in the “dummy
write” portion must match the slave byte in the “read”
section. For a random read of the Clock/Control Registers,
the slave byte must be “1101111x” in both places.
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL1221 responds with an ACK. At this time, the I2C
interface enters a standby state.
Read Operation
A Read operation consists of a three byte instruction
followed by one or more Data Bytes (See Figure 18). The
master initiates the operation issuing the following
sequence: a START, the Identification byte with the R/W bit
set to “0”, an Address Byte, a second START, and a second
Identification byte with the R/W bit set to “1”. After each of
the three bytes, the ISL1221 responds with an ACK. Then
the ISL1221 transmits Data Bytes as long as the master
responds with an ACK during the SCL cycle following the
eighth bit of each byte. The master terminates the read
operation (issuing a STOP condition) following the last bit of
the last Data Byte (See Figure 18).
The Data Bytes are from the memory location indicated by
an internal pointer. This pointer initial value is determined by
the Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 19h the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.
FIGURE 17. SLAVE ADDRESS, WORD ADDRESS, AND DATA
BYTES
SLAVE
ADDRESS BYTE
D7
D6
D5
D2
D4
D3
D1
D0
A0
A7
A2
A4
A3
A1
DATA BYTE
A6
A5
1
10
1
R/W
1
WORD ADDRESS
FIGURE 18. READ SEQUENCE
SIGNALS
FROM THE
MASTER
SIGNALS FROM
THE SLAVE
SIGNAL AT
SDA
S
T
A
R
T
IDENTIFICATION
BYTE WITH
R/W=0
ADDRESS
BYTE
A
C
K
A
C
K
0
S
T
O
P
A
C
K
1
IDENTIFICATION
BYTE WITH
R/W = 1
A
C
K
S
T
A
R
T
LAST READ
DATA BYTE
FIRST READ
DATA BYTE
A
C
K
10
1
1111
10
1
11 11
ISL1221
相關PDF資料 |
PDF描述 |
|---|---|
| ISL26134AVZ | IC ADC 24BIT SRL 80SPS 28TSSOP |
| ISL26319FVZ-T7A | IC ADC 12BIT SRL/SPI 16TSSOP |
| ISL26329FVZ | IC ADC 12BIT SPI/SRL 16-TSSOP |
| ISL2671286IBZ | IC ADC 12BIT SPI/SRL 20K 8SOIC |
| ISL26712IRTZ | IC ADC 12BIT SAR 1MSPS 8-TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL1221IUZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL14010 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Jitter Clock Generators for Set-Top Box |
| ISL14010IRZ | 功能描述:時鐘合成器/抖動清除器 REAL TIME CLKRTC 16LD 3X3 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| ISL14010IRZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC 16LD 3X3 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL14011 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Jitter Clock Generators for Set-Top Box |
發布緊急采購，3分鐘左右您將得到回復。