- 您現在的位置：買賣IC網 > PDF目錄11818 > IS82C50A-5Z (Intersil)IC PERIPH UART/BRG 10MHZ 44-PLCC PDF資料下載
參數資料
| 型號： | IS82C50A-5Z |
| 廠商： | Intersil |
| 文件頁數： | 8/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PERIPH UART/BRG 10MHZ 44-PLCC |
| 標準包裝： | 26 |
| 特點： | 單芯片 UART/BRG |
| 通道數： | 1，UART |
| 規程： | RS232C |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 帶并行端口： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC |
| 包裝： | 管件 |
16
FN2958.5
August 24, 2006
82C50A
Programming
The 82C50A is programmed by the control registers LCR,
lER, DLL and DLM, and MCR. These control words define
the character length, number of stop bits, parity, baud rate,
and modem interface.
While the control registers can be written in any order, the
lER should be written to last because it controls the interrupt
enables. Once the 82C50A is programmed and operational,
these registers can be updated any time the 82C50A is not
transmitting or receiving data.
The control signals required to access 82C50A internal
registers are shown below.
Software Reset
A software reset of the 82C50A is a useful method for
returning to a completely known state without a system
reset. Such a reset consists of writing to the LCR, Divisor
Latches, and MCR registers. The LSR and RBR registers
should be read prior to enabling interrupts in order to clear
out any residual data or status bits which may be invalid for
subsequent operation.
Crystal Operation
The 82C50A crystal oscillator circuitry is designed to operate
with a fundamental mode, parallel resonant crystal. Table 8
shows the required crystal parameters and crystal circuit
configuration, respectively.
When using an external clock source, the XTAL1 input is
driven and the XTAL2 output is left open. Power
consumption when using an external clock is typically 50%
of that required when using a crystal. This is due to the
sinusoidal nature of the drive circuitry when using a crystal.
The maximum frequency of the 82C50A is 10MHz with an
external clock or a crystal attached to XTAL1 and XTAL2.
Using the external clock or crystal, and a divide by one
divisor, the maximum BAUDOUT is 10MHz, and the
maximum data rate is 625Kbps.
TABLE 8. TYPICAL CRYSTAL OSCILLATOR CIRCUIT
PARAMETER
Frequency
1.0 to 10MHz
Type of Operation
Parallel Resonant, Fundamental
Mode
Load Capacitance (CL)
20 or 32pF (Typ)
RSERIES (Max)
100
Ω (f = 10MHz, CL = 32pF)
200
Ω (f = 10MHz, CL = 20pF)
FIGURE 2. TYPICAL CRYSTAL OSCILLATOR CIRCUIT
CL
XTAL
XTAL1
XTAL2
TO
BAUD RATE
GENERATOR
LOGIC
PIN 17
PIN 16
RS
CL
82C50A
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA329-16MUR | MCU AVR 32K FLASH 16MHZ 64QFN |
| CS82C50A-5Z96 | IC ASYNC COMM ELEMNT UART 44PLCC |
| CS82C50A-5Z | IC COMMUNICATION ELEMENT 44-PLCC |
| CP82C52Z | IC UART/BRG 5V 16MHZ 28-PDIP |
| ATUC128D4-AUR | IC MCU 32BIT 128KB FLASH 48TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IS82C52 | 功能描述:UART 接口集成電路 PERIPH UART/BRG 5V 16MHZ 28PLCC IND RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| IS82C52/TR100/BAE | 制造商:Intersil Corporation 功能描述:PERIPH UART/BRG 5V 16MHZ 28PLCC IND - Tape and Reel |
| IS82C5296 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| IS82C52R2490 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| IS82C52Z | 功能描述:UART 接口集成電路 W/ANNEAL PERIPH /BRG 5V 16MHZ RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。