參數資料
型號: IR3093M
廠商: International Rectifier
英文描述: 3 PHASE OPTERON, ATHLON, OR VR10.X CONTROL IC
中文描述: 3相皓龍,速龍,或控制IC的VR10.X
文件頁數: 14/39頁
文件大?。?/td> 693K
代理商: IR3093M
IR3093
Page 14 of 39
07/15/04
VCC Under Voltage Lockout (UVLO)
The VCC UVLO function monitors the IR3093’s VCC supply pin and ensures enough voltage is available to power the
internal circuitry. During power-up the fault latch is reset when VCC exceeds 7.9V and all other faults are cleared. The
fault latch is set when VCC drops below 7.4V and SS/DEL is below 3.75V.
5VUVL Under Voltage Lockout (5VUVL)
The 5VUVL function is provided for converters using a separate voltage supply other than VCC for gate driver bias.
The 5VUVL comparator prevents operation by discharging SS/DEL below 3.75V to force EAOUT low. The 5VUVL
comparator has an OK threshold of 4.36V ensuring adequate gate drive voltage is present and a fault threshold of
4.17V.
Power Good Output
The PWRGD pin is an open-collector output and should be pulled up to a voltage source through a resistor. During soft
start, the PWRGD remains low until the output voltage is in regulation and SS/DEL is above 3.75V. The PWRGD pin
becomes low if the fault latch is set. A high level at the PWRGD pin indicates that the converter is in operation and has
no fault, but does not ensure the output voltage is within the specification. Output voltage regulation within the design
limits can logically be assured however, assuming no component failure in the system.
Tri-State Gate Drivers
The GATELX drivers can pull down up to 3.5A peak current and source up to 1.5A. The GATEHX drivers can source
and sink up to 1.5A peak current. An adaptive non-overlap circuit monitors the voltage on the GATEHX and GATELX
pins to prevent MOSFET shoot-through current while minimizing body diode conduction.
The Error Amplifier output of the Control IC drives low in response to any fault condition such as VCC input under
voltage or output overload. The 0% duty cycle comparator detects this and drives both gate outputs low. This tri-state
operation prevents negative inductor current and negative output voltage during power-down.
The Gate Drivers revert to a high impedance “off” state at VCCLX and VCCHX supply voltages below the normal
operating range. An 80k
UHVLVWRU LV FRQQHFWHG DFURVV WKH *$7(; DQG 3*1'; SLQV WR SUHYHQW WKH *$7(; YROWDJH
from rising due to leakage or other cause under these conditions.
Over Voltage Protection (OVP)
The output Over-Voltage Protection comparator monitors the output voltage through the OVPSNS pin, the positive
remote sense point. If OVPSNS exceeds VDAC plus 150mV (for VR-10.0, 450mV for OPTERON and ATHLON,
selected with the VID_SEL pin), both GATEL pins drive high and the OVP pin sources 75uA current. The OVP circuit
over-rides the normal PWM operation and will fully turn-on the low side MOSFET within approximately 150ns. The low
side MOSFET will remain ON until the over-voltage condition ceases. The lower MOSFETs alone can not clamp the
output voltage however an SCR or N-MOSFET could be triggered with the OVP pin to prevent processor damage.
In the event of a high side MOSFET short, the OVP flag is activated with as little supply voltage as possible. The
OVPSNS pin is compared against both VCC and 5VUVL for OVP conditions at power-up. VCC is monitored for
conversion off 12V, 5VUVL is monitored for conversion off 5V. The OVP pin flags a voltage greater than 0.5V with
supply voltages as low as 1.0V. This headroom voltage varies inversely with temperature. An external comparator
can be used to disable the silver box, activate a crowbar, or supply source.
The overall system must be considered when designing for OVP. In many cases the over-current protection of the AC-
DC or DC-DC converter supplying the multiphase converter will be triggered thus providing effective protection without
damage as long as all PCB traces and components are sized to handle the worst-case maximum current. If this is not
possible, a fuse can be added in the input supply to the multiphase converter.
相關PDF資料
PDF描述
IR3093MTR 3 PHASE OPTERON, ATHLON, OR VR10.X CONTROL IC
IR3080 XPHASE VRD10 CONTROL IC WITH VCCVID & OVERTEMP DETECT
IR3080MTR XPHASE VRD10 CONTROL IC WITH VCCVID & OVERTEMP DETECT
IR3080M XPHASE VRD10 CONTROL IC WITH VCCVID & OVERTEMP DETECT
IR3081 XPHASE VR 10.0 CONTROL IC
相關代理商/技術參數
參數描述
IR3093MPBF 功能描述:IC VID VOLTAGE PROGRAMMER 48MLPQ RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器,監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(5x5) 包裝:帶卷 (TR)
IR3093MTR 制造商:IRF 制造商全稱:International Rectifier 功能描述:3 PHASE OPTERON, ATHLON, OR VR10.X CONTROL IC
IR3093MTRPBF 功能描述:IC CTLR 3PHASE VR10 48-MLQP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器,監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(5x5) 包裝:帶卷 (TR)
IR3094MPBF 功能描述:IC REG CTRLR BUCK PWM VM 48MLPQ RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR)
IR3094MTRPBF 功能描述:開關變換器、穩壓器與控制器 XPHASE VRD10 CTRL IC CTRL IC 200 to 700mV RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel