- 您現在的位置：買賣IC網 > PDF目錄10506 > IL3185E (NVE Corp/Isolation Products)TXRX ISO BUS 5MBPS RS485 16SOIC PDF資料下載
參數資料
| 型號： | IL3185E |
| 廠商： | NVE Corp/Isolation Products |
| 文件頁數： | 2/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX ISO BUS 5MBPS RS485 16SOIC |
| 產品培訓模塊： | IsoLoop® Isolator |
| 產品目錄繪圖： | IL3(1,2,4)85 Circuit |
| 特色產品： | Wide-Body SOIC-16 Isolators |
| 標準包裝： | 50 |
| 系列： | IsoLoop® |
| 類型： | 收發器，隔離式 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS485 |
| 電源電壓： | 3 V ~ 5.5 V，4.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 2771 (CN2011-ZH PDF) |
| 其它名稱： | 390-1095-5 |
IL3185/IL3122
10
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
NVE Corporation
Typical Coil Connections
R
RE
A
B
V
DD2
V
COIL2
V
COIL1
V
DD1
DE
D
R1
16pF ±50%
R2
R3
A
B
Z
R
RE
Y
V
COIL2
V
DD2
V
COIL1
V
DD1
DE
D
R1
R2
R3
16pF ±50%
VDD1 = VDD2 = 5 V
R1, R2, R3 = 820
VDD1 = 3.3 V
R1, R2 = 510 ; R3 = 820
VDD1 = VDD2 = 5 V
R1, R2, R3 = 820
VDD1 = 3.3 V
R1, R2 = 510 ; R3 = 820
Fail-Safe Operation
“Fail-safe operation” is defined here as the forcing of a logic high state on the “R” output in response to an open-circuit condition
between the “A” and “B” lines of the bus, or when no drivers are active on the bus.
Proper biasing can ensure fail-safe operation, that is a known state when there are no active drivers on the bus. IL3185 and IL3122
Isolated Transceivers include internal pull-up and pull-down resistors of approximately 30 k in the receiver section (RFS-INT; see
figure on following page). These internal resistors are designed to ensure failsafe operation but only if there are no termination
resistors. The entire VDD will appear between inputs “A” and “B” if there is no loading and no termination resistors, and there will
be more than the required 200 mV with up to four RS-485/RS-422 worst-case Unit Loads of 12 k. Many designs operating below
1 Mbps or less than 1,000 feet are unterminated. Termination resistors may not be necessary for very low data rates and very short
cable runs because reflections have time to settle before data sampling, which occurs at the middle of the bit interval.
In busses with low-impedance termination resistors, however, the differential voltage across the conductor pair will be close to
zero with no active drivers. In this case the state of the bus is indeterminate, and the idle bus will be susceptible to noise. For
example, with 120 termination resistors (RT) on each end of the cable, and four Unit Loads (12 k each), without external fail-
safe biasing resistors the internal pull-up and pull-down resistors will produce a voltage between inputs “A” and “B” of only about
5 mV. This is not nearly enough to ensure a known state. External fail-safe biasing resistors (RFS-EXT) at one end of the bus can
ensure fail-safe operation with a terminated bus. Resistors should be selected so that under worst-case power supply and resistor
tolerances there is at least 200 mV across the conductor pair with no active drivers to meet the input sensitivity specification of the
RS-422 and RS-485 standards.
Using the same value for pull-up and pull-down biasing resistors maintains balance for positive- and negative going transitions.
Lower-value resistors increase inactive noise immunity at the expense of quiescent power consumption. Note that each Unit Load
on the bus adds a worst-case loading of 12 k across the conductor pair, and 32 Unit Loads add 375 worst-case loading. The
more loads on the bus, the lower the required values of the biasing resistors.
In the example with two 120 termination resistors and four Unit Loads, 560 external biasing resistors provide more than
200 mV between “A” and “B” with adequate margin for power supply variations and resistor tolerances. This ensures a known
state when there are no active drivers. Other illustrative examples are shown in the following table:
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B01-MX-F2 | CONVERTER MOD DC/DC 12V 75W |
| UP050CH3R9K-NAC | CAP CER 3.9PF 50V 10% AXIAL |
| VE-25M-IV-B1 | CONVERTER MOD DC/DC 10V 150W |
| VI-B01-MX-F1 | CONVERTER MOD DC/DC 12V 75W |
| MAX3318CUP+ | IC TXRX RS232 460KBPS 20-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IL3222 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Fractional Load RS485 and RS422 Transceivers |
| IL3222-3E | 功能描述:TXRX ISO BUS 5MBPS RS422 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:IsoLoop® 標準包裝:2,500 系列:- 類型:驅動器 驅動器/接收器數:4/0 規程:RS422 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:帶卷 (TR) |
| IL3222E | 功能描述:TXRX ISO BUS 1MBS RS422 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:IsoLoop® 標準包裝:2,500 系列:- 類型:驅動器 驅動器/接收器數:4/0 規程:RS422 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:帶卷 (TR) |
| IL3222ETR13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Fractional Load RS485 and RS422 Transceivers |
| IL3222TR13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Fractional Load RS485 and RS422 Transceivers |
發布緊急采購，3分鐘左右您將得到回復。