
IBMN364164
IBMN364404
64Mb Synchronous DRAM - Die Revision C
IBMN364804
IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
Page 36 of 71
19L3265.E35856B
1/01
Refreshing
L
L
L
L
L
L
L
L
H
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
L
L
L
L
H
H
H
H
X
L
L
H
H
L
L
H
H
X
L
L
H
H
L
L
H
H
X
L
H
L
H
L
H
L
H
X
L
H
L
H
L
H
L
H
X
OP Code
Mode Register Set
Auto or Self Refresh ILLEGAL
Precharge
Row Address Bank Activate
Column
Write
Column
Read
X
Burst Termination
X
No Operation
X
Device Deselect
OP Code
Mode Register Set
X
Auto or Self Refresh ILLEGAL
X
Precharge
Row Address Bank Activate
Column
Write
Column
Read
X
Burst Termination
X
No Operation
X
Device Deselect
ILLEGAL
X
BS
BS
BS
BS
X
X
X
X
X
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
No Operation; Idle after t
RC
No Operation; Idle after t
RC
No Operation; Idle after t
RC
ILLEGAL
Mode
Register
Accessing
X
BS
BS
BS
BS
X
X
X
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
No Operation; Idle after two clock cycles
No Operation; Idle after two clock cycles
Absolute Maximum Ratings
Symbol
Parameter
Rating
Units
Notes
V
DD
Power Supply Voltage
-0.3 to +4.6
V
1
V
DDQ
Power Supply Voltage for Output
-0.3 to +4.6
V
1
V
IN
Input Voltage
-0.3 to V
DD
+0.3
V
1
V
OUT
Output Voltage
-0.3 to V
DD
+0.3
V
1
T
A
Operating Temperature (ambient)
0 to +70
°
C
1
T
STG
Storage Temperature
-55 to +125
°
C
1
P
D
Power Dissipation
1.0
W
1
I
OUT
Short Circuit Output Current
50
mA
1
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reli-
ability.
Current State Truth Table
(Part 4 of 4)(See note 1)
Current State
Command
Action
Notes
CS
RAS CAS WE A12,A13
A11 - A0
Description
1. CKE is assumed to be active (high) in the previous cycle for all entries. The Current State is the state of the bank that the Com-
mand is being applied to.
2. All Banks must be idle; otherwise, it is an illegal action.
3. If CKE is active (high) the SDRAM will start the Auto (CBR) Refresh operation, if CKE is inactive (low) than the Self Refresh mode
is entered.
4. The Current State refers to only one of the banks. If BS selects this bank then the action is illegal. If BS selects the bank not being
referenced by the Current State then the action may be legal depending on the state of that bank.
5. If CKE is inactive (low) then the Power Down mode is entered; otherwise there is a No Operation.
6. The minimum and maximum Active time (t
RAS
) must be satisfied.
7. The RAS to CAS Delay (t
RCD
) must occur before the command is given.
8. Column address A10 is used to determine if the Auto Precharge function is activated.
9. The command must satisfy any bus contention, bus turn around, and/or write recovery requirements.
10. The command is illegal if the minimum bank to bank delay time (t
RRD
) is not satisfied.