- 您現在的位置：買賣IC網 > PDF目錄384451 > HV312 (Supertex, Inc.) Sequencing Hotswap Controllers PDF資料下載
參數資料
| 型號： | HV312 |
| 廠商： | Supertex, Inc. |
| 英文描述： | Sequencing Hotswap Controllers |
| 中文描述： | 測序熱插拔控制器 |
| 文件頁數： | 5/10頁 |
| 文件大小： | 618K |
| 代理商： | HV312 |
5 Rev. D 04/17/02
HV302 / HV312
Functional Description -
continued
In
Feedback Capacitor Mode
operation, assuming the UV and
OV limits are satisfied and while continuing to hold the PWRGD
flags inactive and the external MOSFET GATE voltage low, the
current source feeding the RAMP pin is turned on. The external
ramp capacitor (C
RAMP
) begins to charge and the feedback
capacitor (C
FB
) begins to discharge, thus starting an initial time
delay determined by the equivalent value of the capacitors and the
2Vbg threshold voltage of the RAMP pin. During this time if the
OV or UV limits are exceeded, an immediate reset occurs, the
ramp capacitor is discharged and the feedback capacitor is
recharged.
When the voltage on the RAMP pin exceeds the 2Vbg threshold
voltage, the gate drive circuit begins to apply voltage to the gate of
the external MOSFET, which begins to turn on when its gate
threshold voltage is reached. However, the source current from
the RAMP pin limits the dv/dt of the feedback capacitor (C
)
which, in turn, programs the inrush current limit (I
CL
) in accordance
with the relationship I
CL
= I
RAMP
x C
LOAD
/C
FB
and thus the dv/dt of the
load capacitor. At this point essentially all available current from
the RAMP pin flows into the feedback capacitor, thus the voltage
on the ramp capacitor and the RAMP pin remains essentially
constant, thereby limiting and controlling the gate voltage of the
external MOSFET (See Programming Current Limit and Circuit
Breaker in Design Information section). When the load capacitor is
fully charged the current flowing into the feedback capacitor is
reduced and the voltage drop across the MOSFET essentially
drops to zero, effectively connecting the feedback capacitor in
parallel with the ramp capacitor. Now the current from the RAMP
pin flows into the parallel-connected capacitors and the voltage on
the RAMP pin begins to rise, thereby providing yet another
programmed delay.
Whether operating in
Servo Mode
or
Feedback Capacitor Mode
,
when the ramp voltage is within 1.2V of the regulated internal
supply voltage, the controller will force the GATE terminal to a
nominal 10V, the PWRGD-A pin will change to an active state and
the Circuit Breaker is enabled. PWRGD-B will change to an active
state a programmed delay time after PWRGD-A went active,
PWRGD-C will change to an active state a programmed delay time
after PWRGD-B went active, PWRGD-D will change to an active
state a programmed delay time after PWRGD-C went active and
the circuit transitions to a low power sleep mode. While in sleep
mode the circuit continues to monitor the current and the OV and
UV status.
When the voltage on the SENSE pin rises to 100mV, indicating an
over current condition, the circuit breaker will trip in less than 5
μ
s.
This time may be extended by the addition of external
components.
If due to output overload conditions during startup full charging of
the load is not achieved within 100ms or a load fault occurs at any
time the circuit breaker is tripped, the MOSFET is turned off by
pulling down the GATE to V
EE
and all four PWRGD flags are reset.
Thereafter an auto-retry timer, programmed by the capacitor
connected to the RAMP pin, will hold the pass device off to allow it
to cool before resetting and restarting. The auto-retry can be
disabled using a single resistor if desired (See Auto-Retry and
Auto-Retry Disable in Design Information section).
At any time during the start up cycle or thereafter, crossing the UV
and OV limits (including hysteresis) will cause an immediate reset
of all internal circuitry. When the input supply voltage returns to a
value within the programmed UV and OV limits a new start up
sequence will be immediately initiated.
Supertex, Inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 TEL: (408) 744-0100 Fax: (408) 222-4895 www.supertex.com
相關PDF資料 |
PDF描述 |
|---|---|
| HV312DB1 | Hotswap Controller |
| HV312NG | Sequencing Hotswap Controllers |
| HV3137 | 64-Channel Serial To Parallel Converter With Open Drain Outputs |
| HV3137PG | 64-Channel Serial To Parallel Converter With Open Drain Outputs |
| HV3137X | 64-Channel Serial To Parallel Converter With Open Drain Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HV312DB1 | 功能描述:電源管理IC開發工具 HV312 Demo Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HV312NG | 功能描述:熱插拔功率分布 Cntl (Act Low) RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV312NG-G | 功能描述:熱插拔功率分布 Cntl (Act Low) RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV312NG-M905 | 功能描述:熱插拔功率分布 -10 to -90V Activ Lw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV312NG-M905-G | 功能描述:熱插拔功率分布 -10 to -90V Activ Lw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。