- 您現在的位置：買賣IC網 > PDF目錄384451 > HV300DB1 (Supertex, Inc.) HV300 Hot Swap Demo Board PDF資料下載
參數資料
| 型號： | HV300DB1 |
| 廠商： | Supertex, Inc. |
| 英文描述： | HV300 Hot Swap Demo Board |
| 中文描述： | HV300熱插拔演示板 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 78K |
| 代理商： | HV300DB1 |
HV300/HV310
4
Pinout
Pin Description
PWRGD –
The Power Good Output Pin is held inactive on initial
power application and will go active when the external MOSFET
is fully turned on. This pin may be used as an enable control
when connected directly to a PWM power module.
OV –
This Over Voltage sense pin, when raised above its high
threshold will immediately cause the GATE pin to be pulled low.
The GATE pin will remain low until the voltage on this pin falls
below the low threshold limit, initiating a new start-up cycle.
UV
– This Under Voltage sense pin, when below its low threshold
limit will ensure that the GATE pin is low. The GATE pin will
remain low until the voltage on this pin rises above the high
threshold, initializing a new start-up cycle.
V
EE
– This pin is the negative voltage power supply input to the
circuit.
V
DD
–
This pin is the positive voltage power supply input to the
circuit.
RAMP –
This pin provides a current output so that a timing
ramp voltage is generated when a capacitor is connected. The
initial portion of the ramp provides a time delay, which in
conjunction with the Under Voltage detection circuit eliminates
circuit card insertion contact bounce. The RAMP pin also controls
the delay between the current limit mode disengaging and the
PWRGD signal activating; as well as the current rise profile
after the initial turn on delay.
GATE –
This is the Gate Driver Output for the external N-
Channel MOSFET.
SENSE –
The current sense resistor connected from this pin to
V
EE
pin programs the current limit. Constant current output
mode is established when the voltage drop across this resistor
reaches 50mV.
Functional Block Diagram
1
2
3
4
8
7
6
5
PWRGD
V
DD
RAMP
OV
UV
GATE
V
EE
SENSE
PWRGD Logic
Model
Condition
PWRGD
HV300
NOT READY
0
V
EE
HI Z
READY
1
HV310
NOT READY
1
HI Z
READY
0
V
EE
Buffer
LOGIC
V
INT
V
DD
UV
OV
V
EE
SENSE
GATE
RAMP
Vref
UVLO
and
POR
Band Gap
Reference
Internal
Supply
Regulator
VINT
V
INT –1.2V
Vref
HV300:PWRG
HV310: PWRGD
+
–
10μA
Trans-
conductor
V
REF
5k
相關PDF資料 |
PDF描述 |
|---|---|
| HV300LG | Hotswap, Inrush Current Limiter Controllers |
| HV310 | Hotswap, Inrush Current Limiter Controllers |
| HV310LG | Hotswap, Inrush Current Limiter Controllers |
| HV301 | Hotswap, Controllers with Circuit Breaker |
| HV301LG | Hotswap, Controllers with Circuit Breaker |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HV300DB2 | 功能描述:電源管理IC開發工具 HV300 Demo Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HV300LG | 功能描述:熱插拔功率分布 Active High RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV300LG-G | 功能描述:熱插拔功率分布 Active High RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV300LG-M908 | 功能描述:熱插拔功率分布 -10 to -90V Activ Hi RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV300LG-M908-G | 功能描述:熱插拔功率分布 -10 to -90V Activ Hi RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。