- 您現在的位置：買賣IC網 > PDF目錄385409 > HV111 (Supertex, Inc.) Inrush Limiter/Circuit Breaker/Hotswap Controller IC PDF資料下載
參數資料
| 型號： | HV111 |
| 廠商： | Supertex, Inc. |
| 元件分類： | 脈沖抑制器 |
| 英文描述： | Inrush Limiter/Circuit Breaker/Hotswap Controller IC |
| 中文描述： | 浪涌電流限制器/斷路器/熱插拔控制器IC |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 551K |
| 代理商： | HV111 |
HV111
Thermal Shutdown
Auto-Retry
In addition to the above parameters, the HV111 will
shutdown if the temperature on the die reaches ~135°C and
it will not restart until the temperature drops to 100°C or less
(could be significantly less). The thermal sensor is key in
providing a bullet proof power management solution
because it ensures that the device will turn off long before
damage can occur. This is a significant advantage over
solutions that do not contain an integral MOSFET as then
the temperature cannot be easily sensed quickly and
accurately.
Any fault condition will cause an automatic 9sec retry to
occur. This retry will occur indefinitely (as long as the
thermal supervisor is satisfied). Figure 6 shows typical
waveforms for the auto-retry.
Timers
50V/div
200ma/div
PWRGD
V
PP
-V
NN
I
DS
Thermal engineering using the HV111 is key to proper
system operation. The 1
MOSFET pass element may
reach a value as high as 1.5
at high temperatures. There
are numerous methods to reduce the thermal resistance of
the R
θ
JA
. The following table describes some options:
Method
FR4
FR4 Heat Sink
R
θ
JA
Description
Straight Convection
10cm
70-80° C/W
40° C/W
2
PCB H/S
FR4 + H/S
13° C/W
External Sink + Holes
IMS (40cm
IMS* w/ H/S
* IMS is a metal substrate board
2
)
9° C/W
4.5° C/W
Floating in Air
External Heatsink
The timer subsystems are critical to successful operation of
the HV111. Timers are as follows:
To determine your required thermal impedance, R
θ
JA
, is quite
simple. In a parallel to Ohms law, Power x
R
θ
=
T.
Junction temperature, which is limited to 120
°
C minimum, is
Tmaxambient +
T. For example, if the highest operating
ambient temperature were 55
°
C as with many networking
applications, and the current were 1.6A, then the required
thermal resistance would be calculated as follows:
Timer
Power-on-Reset
Initial Inrush Timeout
Shorted Inrush PWM
Shorted Circuit Timer
Second Inrush (Diode
‘OR’ing):
Return to Limit
Timeout
Auto-Retry
Duration
4.5ms
75ms
10
μ
s
75ms
10
μ
s
(100
μ
s)
75ms
9sec
1
2
3
Determine maximum ambient = 55
°
C.
Determine max junction temp. = 120
°
C
1
.
Determine max operating current = 1.6A.
Therefore
T = 120-55
°
C = 65
°
C.
1
This is the time from satisfying the undervoltage comparator. Each “bounce” will reset this
timer & therefore observed delay may be higher than this “ideal” delay.
Max. Power
2
= 1.23A
2
*1.5
= 3.84W.
Now
T / Power = R
θ
JA
= 65
°
/3.84W = 20
°
C/W.
To achieve a R
θ
of 20
°
C/W or better the table above shows
that it will be necessary to use a DPAK external heatsink or
IMS substrate.
1
This is the minimum value of the low to high thermal shutdown according to the electrical
specifications on pg. 2.
2
This is the maximum MOSFET on resistance at high temperature.
2
Shorted-circuit timer starts after POR timer. If V
DS
drops more than (V
PP
-V
NN
) after t
SC
then a shorted-circuit condition exists.
3
Limit within 10
μ
s, but may take up to 100
μ
s to settle.
Current Sensing – No R
SENSE
Required
The HV111 uses an internal 6000:1 current mirror to
eliminate the need for a sense resistor. This saves energy
and eliminates the need for a power component. The current
mirror used by Supertex is unique in that it utilizes special
circuitry to normalize for the variations in V
between the
primary pass element and the internal element which would
otherwise cause current mismatch – and forces competitors
to use internal sense resistors in similar applications. This
mechanism also provides the shorted circuit PWM
functionality which can help protect systems in the case of
severe short circuits.
5
相關PDF資料 |
PDF描述 |
|---|---|
| HV111K4 | Inrush Limiter/Circuit Breaker/Hotswap Controller IC |
| HV219 | Low Charge Injection 8-Channel High Voltage Analog Switch |
| HV219FG | Low Charge Injection 8-Channel High Voltage Analog Switch |
| HV219PJ | Low Charge Injection 8-Channel High Voltage Analog Switch |
| HV219X | Low Charge Injection 8-Channel High Voltage Analog Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HV111K4 | 功能描述:熱插拔功率分布 3/1 Controller IC RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV113SM-12 | 制造商:SPECTRUM 制造商全稱:Spectrum Microwave, Inc. 功能描述:Voltage Controlled Oscillator |
| HV113T-1 | 制造商:SPECTRUM 制造商全稱:Spectrum Microwave, Inc. 功能描述:Voltage Controlled Oscillator |
| HV116 | 制造商:Apex Tool Group 功能描述:1 IN. X 16 FT HI-VIZ ORANGE SERIES POWER RETURN TAPE |
| HV12 | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:FAST RECOVERY HIGH VOLTAGE DIODES |
發布緊急采購，3分鐘左右您將得到回復。