- 您現在的位置：買賣IC網 > PDF目錄385404 > HT82K96E (Holtek Semiconductor Inc.) 8-Bit USB Multimedia Keyboard Encoder OTP MCU PDF資料下載
參數資料
| 型號： | HT82K96E |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit USB Multimedia Keyboard Encoder OTP MCU |
| 中文描述： | 8位USB多媒體鍵盤編碼器檢察官辦公室單片機 |
| 文件頁數： | 23/46頁 |
| 文件大?。?/td> | 325K |
| 代理商： | HT82K96E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
HT82K96E
Rev. 1.70
23
April 22, 2004
The definitions of the USB/PS2 status and control register (USC; 1AH) are as shown.
USC
Bits
R/W
Function
SUSP
0
R
Read only, USB suspend indication. When this bit is set to 1 (set by SIE), it indi-
cates the USB bus enters suspend mode. The USB interrupt is also triggered on any
changing of this bit.
RMWK
1
W
USB remote wake up command. It is set by MCU to force the USB host leaving the
suspend mode. When this bit is set to 1 , 2 s delay for clearing this bit to 0 is
needed to insure the RMWK command is accepted by SIE.
URST
2
R/W
USB reset indication. This bit is set/cleared by USB SIE. This bit is used to detect
which bus (PS2 or USB) is attached. When the URST is set to 1 , this indicates an
USB reset is occurred (The attached bus is USB) and an USB interrupt will be initial-
ized.
RESUME
3
R
USB resume indication. When the USB leaves suspend mode, this bit is set to 1
(set by SIE). This bit will appear 20ms waiting for MCU to detect. When the RE-
SUME is set by SIE, an interrupt will be generated to wake-up the MCU. In order to
detecting the suspend state, MCU should set USBCKEN and clear SUSP2 (in SCC
register) to enable the SIE detecting function. The RESUME will be cleared while
the SUSP is going 0 . When MCU is detecting the SUSP, the RESUME (causes
MCU to wake-up) should be remembered and token into consideration.
PS2DAI
4
R
Read only, USBD-/DATA input
PS2CKI
5
R
Read only, USBD+/CLK input
PS2DAO
6
W
Data for driving USBD-/DATA pin when work under 3D PS2 mouse function.
(Default= 1 )
PS2CKO
7
W
Data for driving USBD+/CLK pin when work under 3D PS2 mouse function.
(Default= 1 )
The USR (USB endpoint interrupt status register) register is used to indicate which endpoint is accessed and to select
serial bus (PS2 or USB) and A/D converter operation modes. The endpoint request flags (EP0IF, EP1IF, EP2IF and
EP3IF) are used to indicate which endpoints are accessed. If an endpoint is accessed, the related endpoint request
flag will be set to 1 and the USB interrupt will occur (if USB interrupt is enabled and the stack is not full). When the ac-
tive endpoint request flag is served, the endpoint request flag has to be cleared to 0 .
USR
Bits
R/W
Function
EP0IF
0
R/W
When this bit is set to 1 (set by SIE), it indicates the endpoint 0 is accessed and an
USB interrupt will occur. When the interrupt has been served, this bit should be
cleared by firmware.
EP1IF
1
R/W
When this bit is set to 1 (set by SIE), it indicates the endpoint 1 is accessed and an
USB interrupt will occur. When the interrupt has been served, this bit should be
cleared by firmware.
EP2IF
2
R/W
When this bit is set to 1 (set by SIE), it indicates the endpoint 2 is accessed and an
USB interrupt will occur. When the interrupt has been served, this bit should be
cleared by firmware.
EP3IF
3
R/W
When this bit is set to 1 (set by SIE), it indicates the endpoint 3 is accessed and an
USB interrupt will occur. When the interrupt has been served, this bit should be
cleared by firmware.
SPS2
4
R/W The PS2 function is selected when this bit is set to 1 . (Default= 0 )
SUSB
5
R/W The USB function is selected when this bit is set to 1 . (Default= 0 )
ADREF
6
R/W
The reference voltage of A/D converter is coming from the VDD and VSS of MCU
when this bit is set 1 . Otherwise, the reference voltage of A/D converter comes
from external PB6/VRL and PB7/VRH pins. (Default= 1 )
FIFO-cntl
7
W
For ICE only, 0 for FIFO read (Default= 0 ); 1 for FIFO write
相關PDF資料 |
PDF描述 |
|---|---|
| HT82M21A | 3-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M22 | 5-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M22A | 5-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M23C | 3/5-Key USB+PS/2 Optical Mouse Controller |
| HT82M23A | 3/5-Key USB+PS/2 Optical Mouse Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82K96E_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit OTP MCU |
| HT82M13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Mouse/Trackball Controller |
| HT82M21A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:3-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M21A_05 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:3-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M22 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:5-Key 3D USB+PS/2 Optical Mouse Controller |
發布緊急采購，3分鐘左右您將得到回復。