- 您現在的位置：買賣IC網 > PDF目錄385404 > HT82K95AE (Holtek Semiconductor Inc.) USB Multimedia Keyboard Encoder 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT82K95AE |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | USB Multimedia Keyboard Encoder 8-Bit MCU |
| 中文描述： | 的USB多媒體鍵盤編碼器8位微控制器 |
| 文件頁數： | 16/45頁 |
| 文件大小： | 297K |
| 代理商： | HT82K95AE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
HT82K95EE/HT82K95AE
Rev. 1.20
16
August 28, 2006
ofTMR0C/TMR1C)shouldbesetto1.Inthepulsewidth
measurement mode, the TON will be cleared automati-
cally after the measurement cycle is completed. But in
the other two modes the TON can only be reset by in-
structions. The overflow of the Timer/Event Counter 0/1
is one of the wake-up sources. No matter what the oper-
ation mode is, writing a 0 to ET0I/ET1I can disable the
corresponding interrupt services.
In the case of Timer/Event Counter 0/1 OFF condition,
writingdatatotheTimer/EventCounter0/1preloadregis-
ter will also reload that data to the Timer/Event Counter
0/1. But if the Timer/Event Counter 0/1 is turned on, data
written to it will only be kept in the Timer/Event Counter
0/1preloadregister.TheTimer/EventCounter0/1willstill
operate until overflow occurs (a Timer/Event Counter 0/1
reloading will occur at the same time). When the
Timer/Event Counter 0/1 (reading TMR0/TMR1) is read,
theclockwillbeblockedtoavoiderrors.Asclockblocking
may results in a counting error, this must be taken into
consideration by the programmer.
Input/Output Ports
There are 32 bidirectional input/output lines in the
microcontroller, labeled from PA to PD, which are
mapped to the data memory of [12H], [14H], [16H] and
[18H] respectively. All of these I/O ports can be used for
input and output operations. For input operation, these
ports are non-latching, that is, the inputs must be ready
at the T2 rising edge of instruction MOVA,[m] (m=12H,
14H, 16H or 18H). For output operation, all the data is
latched and remains unchanged until the output latch is
rewritten.
Each I/O line has its own control register (PAC, PBC,
PCC, PDC) to control the input/output configuration.
With this control register, CMOS/NMOS/PMOS output
or Schmitt trigger input with or without pull-high resistor
structures can be reconfigured dynamically under soft-
ware control. To function as an input, the corresponding
latch of the control register must write a 1 . The input
source also depends on the control register. If the con-
trol register bit is 1 , the input will read the pad state. If
the control register bit is 0 , the contents of the latches
will move to the internal bus. The latter is possible in the
read-modify-write
CMOS/NMOS/PMOS configurations can be selected
(NMOS and PMOS are available for PA only). These
controlregistersaremappedtolocations13H,15H,17H
and 19H.
instruction. For output function,
Afterachipreset,theseinput/outputlinesremainathigh
levels or floating state (depending on the pull-high op-
tions). Each bit of these input/output latches can be set
or cleared by SET [m].i and CLR [m].i (m=12H, 14H,
16H or 18H) instructions.
Some instructions first input data and then follow the
output operations. For example,
SET [m].i ,
CLR
[m].i , CPL [m] , CPLA[m] read the entire port states
into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or the accumulator.
Each line of all the I/O ports have the capability of wak-
ing up the device.
There are pull-high (PA only) options available for I/O
lines. Once the pull-high option of an I/O line is selected,
the I/O line have pull-high resistor. Otherwise, the
pull-high resistor is absent. It should be noted that a
non-pull-high I/O line operating in input mode will cause
a floating state.
It is recommended that unused or not bonded out I/O
linesshouldbesetasoutputpinsbysoftwareinstruction
to avoid consuming power under input floating state.
-
0
1 )
. )
/
-
/ 0
/ 1 )
#
/ . )
-
.
-
.
" (
(
!
, ( /
, , 4 $
$
( /
!
+
(
, (
!
$
(
!
" (
, (
!
+
(
(
!
( /
, , 4 , A
+
<
4
( %
(
( )
(
. )
(
%
+
<
4
(
( %
(
( )
(
F
F
F
F
Input/Output Ports
相關PDF資料 |
PDF描述 |
|---|---|
| HT82K95EE | USB Multimedia Keyboard Encoder 8-Bit MCU |
| HT82K95A | USB Multimedia Keyboard Encoder 8-Bit MCU |
| HT82K95E | USB Multimedia Keyboard Encoder 8-Bit MCU |
| HT82K96A | USB Multimedia Keyboard Encoder 8-Bit Mask MCU |
| HT82K96E | 8-Bit USB Multimedia Keyboard Encoder OTP MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82K95E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit MCU |
| HT82K95EE | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit MCU |
| HT82K96A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit Mask MCU |
| HT82K96E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit USB Multimedia Keyboard Encoder OTP MCU |
| HT82K96E_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit OTP MCU |
發布緊急采購，3分鐘左右您將得到回復。