參數資料
型號： HT82K94E_07
廠商： Holtek Semiconductor Inc.
英文描述： USB Multimedia Keyboard Encoder 8-Bit MCU
中文描述： 的USB多媒體鍵盤編碼器8位微控制器
文件頁數： 20/43頁
文件大小： 293K
代理商： HT82K94E_07
HT82K94E/HT82K94A
Rev. 1.50
20
October 11, 2007
Func. Name
R/W
Description
CRC_ERR
R/W
This bit is used to indicate there are CRCerror (bit=1). Firmware must do something to
save the device and keep it in good condition.
This bit is set by SIE and cleared by F/W.
EOT
R
End of transaction flag, normal status is 1. If suspend= 1 line & EOT= 0 indicates that
something is wrong in the USB Interface. Firmware in-charge must do something to
save the device and keep it in good condition.
NMI
R/W
This bit is used to control whether the USB interrupt is output to the MCU in NAK re-
sponse to the PC Host IN or OUT token.
1: has only USB interrupt, data is transmitted to the PC host or data is received from
the PC Host
0: always has USB interrupt if the USB accesses FIFO0
Default 0
SIES Function
MISC register combines a command and status to control desired endpoint FIFO action and to show the status of the
desired endpoint FIFO. The MISC will be cleared by USB reset signal.
Bit No.
Label
R/W
Function
0
REQ
R/W
After setting the other status of the desired one in the MISC, endpoint FIFO can be
requested by setting this bit to 1 . After the job has been done, this bit has to be
cleared to 0 .
1
TX
R/W
This bit defines the direction of data transferring between MCU and endpoint FIFO.
When the TX is set to 1 , this means that the MCU wants to write data to the end-
point FIFO. After the job has been done, this bit has to be cleared to 0 before termi-
nating request to represent the end of transferring. For reading action, this bit has to
be cleared to 0 to represent that MCU wants to read data from the endpoint FIFO
and has to be set to 1 after the job is done.
2
CLEAR
R/W
Clear the requested endpoint FIFO, even if the endpoint FIFO is not ready.
4
3
SELP1
SELP0
R/W
Defines which endpoint FIFO is selected, SELP1,SELP0:
00: endpoint FIFO0
01: endpoint FIFO1
10: endpoint FIFO2
11: endpoint FIFO3
5
SCMD
R/W
Used to show that the data in endpoint FIFO is a SETUP command. This bit has to
beclearedbyfirmware.Thatistosay,eventheMCUisbusy,thedevicewillnotmiss
any SETUP commands from the host.
6
READY
R
Read only status bit, this bit is used to indicate that the desired endpoint FIFO is
ready to work.
7
LEN0
R/W
Used to indicate that a 0-sized packet is sent from a host to the MCU. This bit should
be cleared by firmware.
MISC (46H) Register
The MCU can communicate with the endpoint FIFO by setting the corresponding registers, of which address is listed in
the following table. After reading the current data, next data will show after 2 s, used to check the endpoint FIFO status
and response to MISC register, if read/write action is still going on.
Registers
R/W
Bank
Address
Bit7~Bit0
FIFO0
R/W
1
48H
Data7~Data0
FIFO1
R/W
1
49H
Data7~Data0
FIFO2
R/W
1
4AH
Data7~Data0
FIFO3
R/W
1
4BH
Data7~Data0
相關PDF資料
PDF描述
HT82K95AE USB Multimedia Keyboard Encoder 8-Bit MCU
HT82K95EE USB Multimedia Keyboard Encoder 8-Bit MCU
HT82K95A USB Multimedia Keyboard Encoder 8-Bit MCU
HT82K95E USB Multimedia Keyboard Encoder 8-Bit MCU
HT82K96A USB Multimedia Keyboard Encoder 8-Bit Mask MCU
相關代理商/技術參數
參數描述
HT82K95A 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit MCU
HT82K95AE 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit MCU
HT82K95E 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit MCU
HT82K95EE 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit MCU
HT82K96A 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit Mask MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*