- 您現(xiàn)在的位置：買賣IC網 > PDF目錄385398 > HT36A2 (Holtek Semiconductor Inc.) 8-Bit Music Synthesizer MCU PDF資料下載
參數資料
| 型號： | HT36A2 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit Music Synthesizer MCU |
| 中文描述： | 8位微控制器音樂合成器 |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 215K |
| 代理商： | HT36A2 |
HT36A2
Rev. 1.00
16
June 19, 2003
CH[2~0] channel number selection
The HT36A2 has a built-in 8 output channels and
CH[2~0] is used to define which channel is selected.
When this register is written to, the wavetable synthe-
sizer will automatically output the dedicated PCM
code. So this register is also used as a start playing
key and it has to be written to after all the other
wavetable function registers are already defined.
Change parameter selection
These two bits, VM and FR, are used to define which
register will be updated on this selected channel.
There are two modes that can be selected to reduce
the process of setting the register. Please refer to the
statements of the following table:
VM
FR
Function
0
0
Update all the parameter
0
1
Only update the frequency number
1
0
Only update the volume
Output frequency definition
The data on BL[3~0] and FR[11~0] are used to define
the output speed of the PCM file, i.e. it can be used to
generate the tone scale. When the FR[11:0] is 800H
and BL[3:0] is 6H, each sample data of the PCM code
will be sent out sequentially.
When the f
OSC
is 6.4MHz, the formula of a tone fre-
quency is:
25kHz
FR [11~ 0]
f
OUT
= f
RECORD
′
′
SR
2
(17-
where f
OUT
is the output signal frequency, f
RECORD
and
SR is the frequency and sampling rate on the sample
code, respectively.
So if a voice code of C3 has been recorded which has
the f
RECORD
of 261Hz and the SR of 11025Hz, the tone
frequency (f
OUT
) of G3: f
OUT
=98Hz.
Can be obtained by using the fomula:
25kHz
′
98Hz= 261Hz
11025Hz
FR[11~ 0]
2
(17-
A pair of the values FR[11~0] and BL[3~0] can be de-
termined when the f
OSC
is 6.4MHz.
Start address definition
The HT36A2 provides two address types for extended
use, one is the program ROM address which is pro-
gram counter corresponding with PF value, the other
is the start address of the PCM code.
The ST[11~0] is used to define the start address of
each PCM code and reads the waveform data from
this location. The HT36A2 provides 16 input data lines
from WA[15~0], the ST[11~0] is used to locate the ma-
jor 12 bits i.e. WA[15~5] and the undefined data from
WA[4~0] is always set as 00000b. In other words, the
WA[15~0]=ST[11~0] 2
5
. So each PCM code has to
be located at a multiple of 32. Otherwise, the PCM
code will not be read out correctly because it has a
wrong start code.
Waveform format definition
The HT36A2 accepts two waveform formats to ensure
a more economical data space. WBS is used to define
the sample format of each PCM code.
WBS=0 means the sample format is 8-bit
WBS=1 means the sample format is 12-bit
The 12-bit sample format allocates location to each
sample data. Please refer to the waveform format
statement as shown below.
Repeat number definition
The repeat number is used to define the address
which is the repeat point of the sample. When the re-
peat number is defined, it will be output from the start
code to the end code once and always output the
range between the repeat address to the end code
(80H) until the volume become close.
The RE[9~0] is used to calculate the repeat address
of the PCM code. The process for setting the RE[9~0]
is to write the 2 s complement of the repeat length to
RE[9~0], with the highest carry ignored. The HT36A2
will get the repeat address by adding the RE[9~0] to
the address of the end code, then jump to the address
to repeat this range.
Volume control
The HT36A2 provides the volume control independ-
ently. The volume are controlled by VR[9~0] respec-
tively. The chip provides 1024 levels of controllable
volume, the 000H is the maximum and 3FFH is the
minimum output volume.
!
+
2
=
=
2
! 2
!
(
9
< (
( 0 :
G (
( 9
( :
(
( 1
5
! =
- :
@ C
2 C ( 2
<
( -
C
C (
( -
C
= C ( = : > ( -
(
9
< (
( 0 :
Waveform format
相關PDF資料 |
PDF描述 |
|---|---|
| HT36A3 | 8-Bit Music Synthesizer MCU |
| HT36A4 | 8-Bit Music Synthesizer MCU |
| HT3810 | 128 NOTE MELODY GENERATORS |
| HT3810A | 128 NOTE MELODY GENERATORS |
| HT3810B | 128 NOTE MELODY GENERATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT36A3 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Music Synthesizer MCU |
| HT36A4 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Music Synthesizer 8-Bit MCU |
| HT36A4_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Music Synthesizer 8-Bit MCU |
| HT36ARP | 功能描述:兩端交流開關元件 32-40V RoHS:否 制造商:STMicroelectronics 轉折電流 VBO:45 V 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 封裝:Reel |
| HT36B | 功能描述:兩端交流開關元件 34-38V RoHS:否 制造商:STMicroelectronics 轉折電流 VBO:45 V 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。