- 您現在的位置：買賣IC網 > PDF目錄385398 > HT36A1 (Holtek Semiconductor Inc.) Music Synthesizer 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT36A1 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | Music Synthesizer 8-Bit MCU |
| 中文描述： | 音樂合成器8位微控制器 |
| 文件頁數： | 14/39頁 |
| 文件大小： | 286K |
| 代理商： | HT36A1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
HT36A1
Rev. 1.00
14
August 15, 2005
Timer 0/1
Timer 0 is an 8-bit counter, and its clock source comes
from the system clock divided by an 8-stage prescaler.
There are two registers related to Timer 0; TMR0L(0DH)
and TMR0C(0EH). One physical registers are mapped
to TMR0L location; writing TMR0L makes the starting
value be placed in the Timer 0 preload register and
readingtheTMR0getsthecontentsoftheTimer0coun-
ter. The TMR0C is a control register, which defines the
division ration of the prescaler and counting enable or
disable.
Writing data to B2, B1 and B0 (bits 2, 1, 0 of TMR0C)
can yield various clock sources.
One the Timer 0 starts counting, it will count from the
current contents in the counter to FFH. Once an over-
flow occurs, the counter is reloaded from a preload reg-
ister, and generates an interrupt request flag (T0F; bit 2
of INTCH). To enable the counting operation, the timer
On bit (TON; bit 4 of TMR0C) should be set to 1 . For
proper operation, bit 7 of TMR0C should be set to 1
and bit 3, bit 6 should be set to 0 .
There are two registers related to the Timer Counter1;
TMR1L(10H), TMR1C(11H). The Timer Counter 1 oper-
ates in the same manner as Timer Counter 0.
TMR0C/TMR1C
T0F
B2
B1
B0
0
0
0
SYS CLK/16
0
0
1
SYS CLK/32
0
1
0
SYS CLK/64
0
1
1
SYS CLK/128
1
0
0
SYS CLK/256
1
0
1
SYS CLK/512
1
1
0
SYS CLK/1024
1
1
1
SYS CLK/2048
TMR0C Bit 4 to enable/disable timer counting
(1=enable; 0=disable)
TMR0C Bit 3, always write 0 .
TMR0C Bit 5, always write 0 .
TMR0C Bit 6, always write 0 .
TMR0C Bit 7, always write 1 .
Input/Output Ports
There are 24 bidirectional input/output lines labeled
from PAto PC, which are mapped to the data memory of
[12H], [14H], [16H] respectively. All these I/O ports can
be used for input and output operations. For input oper-
ation, these ports are non-latching, that is, the inputs
must be ready at the T2 rising edge of instruction MOV
A,[m] (m=12H, 14H or 16H). For output operation, all
data is latched and remains unchanged until the output
latch is rewritten.
Each I/O line has its own control register (PAC, PBC,
PCC) to control the input/output configuration. With this
control register, CMOS output or Schmitt trigger input
with or without pull-high resistor (mask option) struc-
tures can be reconfigured dynamically under software
control. To function as an input, the corresponding latch
of the control register must write a 1 . The pull-high re-
sistance will exhibit automatically if the pull-high option
is selected. The input source also depends on the con-
trol register. If the control register bit is 1 , input will
read the pad state. If the control register bit is 0 , the
contents of the latches will move to the internal bus. The
latter is possible in read-modify-write instruction. For
output function, CMOS is the only configuration. These
control registers are mapped to locations 13H, 15H and
17H.
Afterachipreset,theseinput/outputlinesremainathigh
levels or floating (mask option). Each bit of these in-
put/output latches can be set or cleared by the SET [m].i
or CLR [m].i (m=12H, 14H or 16H) instruction.
Some instructions first input data and then follow the
output operations. For example, the SET [m].i, CLR
[m].i, CPL [m] and CPLA [m] instructions read the entire
port states into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or the accumulator.
Each line of port A has the capability to wake-up the de-
vice.
! 2
:
; 1 4
=
1
6 :
)
;
)
=
6 :
)
#
)
;
A
< ; >
6
.
6
/
Timer 0/1
C
# 6
&
% 6
C
# 6
6 :
;
" !
;
C
: )
; >
;
) #
1
=
! ! 6
=
)
;
!
7
Reset Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| HT36A2 | 8-Bit Music Synthesizer MCU |
| HT36A3 | 8-Bit Music Synthesizer MCU |
| HT36A4 | 8-Bit Music Synthesizer MCU |
| HT3810 | 128 NOTE MELODY GENERATORS |
| HT3810A | 128 NOTE MELODY GENERATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT36A2 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Music Synthesizer MCU |
| HT36A3 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Music Synthesizer MCU |
| HT36A4 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Music Synthesizer 8-Bit MCU |
| HT36A4_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Music Synthesizer 8-Bit MCU |
| HT36ARP | 功能描述:兩端交流開關元件 32-40V RoHS:否 制造商:STMicroelectronics 轉折電流 VBO:45 V 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。