參數資料
型號: HT27LC020
廠商: Holtek Semiconductor Inc.
英文描述: OTP CMOS 256Kx 8-Bit EPROM
中文描述: 檢察官辦公室的CMOS 256Kx 8位存儲器
文件頁數: 5/15頁
文件大?。?/td> 203K
代理商: HT27LC020
HT27LC020
Rev. 1.50
5
December 8, 2003
Functional Description
Operation Mode
All the operation modes are shown in the table following.
Mode
CE
OE
PGM
A0
A1
A9
VPP
Output
Read
V
IL
V
IL
X (2)
X
X
X
V
CC
Dout
Output Disable
V
IL
V
IH
X
X
X
X
V
CC
High Z
Standby (TTL)
V
IH
X
X
X
X
X
V
CC
High Z
Standby (CMOS)
V
CC
0.3V
X
X
X
X
X
V
CC
High Z
Program
V
IL
V
IH
V
IL
X
X
X
V
PP
D
IN
Program Verify
V
IL
V
IL
V
IH
X
X
X
V
PP
D
OUT
Product Inhibit
V
IH
X
X
X
X
X
V
PP
High Z
Manufacturer Code (3)
V
IL
V
IL
X
V
IL
V
IH
V
H
(1)
V
CC
1C
Device Code (3)
V
IL
V
IL
X
V
IH
V
IH
V
H
(1)
V
CC
02
Notes: (1) V
H
= 12.0V 0.5V
(2) X=Either V
IH
or V
IL
(3) For Manufacturer Code and Device Code, A1=V
IH
, When A1=V
IL
, both codes will read 7F
Programming of the HT27LC020
When the HT27LC020 is delivered, the chip has all
2048K bits in the ONE , or HIGH state. ZEROs are
loaded into the HT27LC020 through programming.
The programming mode is entered when 12.5 0.2V is ap-
plied to the VPP pin, OE is at V
IH
, and CE and PGM are
V
IL
. For programming, the data to be programmed is ap-
plied with 8 bits in parallel to the data pins.
The programming flowchart in Figure 3 shows the fast
interactive programming algorithm. The interactive al-
gorithm reduces programming time by using 30 s to
105 s programming pulses and giving each address
only as many pulses as is necessary in order to reliably
program the data. After each pulse is applied to a given
address, the data in that address is verified. If the data
is not verified, additional pulses are given until it is veri-
fied or until the maximum number of pulses is reached
while sequencing through each address of the
HT27LC020. This process is repeated while sequenc-
ing through each address of the HT27LC020. This part
of the programming algorithm is done at V
CC
=6.0V to
assure that each EPROM bit is programmed to a suffi-
ciently high threshold voltage. This ensures that all bits
have sufficient margin. After the final address is com-
pleted, the entire EPROM memory is read at
V
CC
=V
PP
=3.3 0.3V to verify the entire memory.
Program inhibit Mode
Programming of multiple HT27LC020 in parallel with dif-
ferent data is also easily accomplished by using the Pro-
gram Inhibit Mode. Except for CE, all like inputs of the
parallel HT27LC020 may be common. A TTL low-level pro-
gram pulse applied to an HT27LC020 CE input with V
PP
=
12.5 0.2V, PGM Low, and OE High will program that
HT27LC020. A high-level CE input inhibits the HT27LC020
from being programmed.
Program Verify Mode
Verification should be performed on the programmed
bits to determine whether they were correctly pro-
grammed. The verification should be performed with
OE and CE at V
IL
, PGM at V
IH
, and VPP at its program-
ming voltage.
Auto Product Identification
The Auto Product Identification mode allows the read-
ingoutofabinarycodefromanEPROMthatwillidentify
its manufacturer and the type. This mode is intended for
programming to automatically match the device to be
programmed with its corresponding programming algo-
rithm. This mode is functional in the 25 C 5 C ambient
temperature range that is required when programming
the HT27LC020.
To activate this mode, the programming equipment must
force 12.0 0.5V on the address line A9 of the
HT27LC020. Two identifier bytes may then be sequenced
from the device outputs by toggling address line A0 from
V
IL
to V
IH
, when A1=V
IH
. All other address lines must be
held at V
IH
during Auto Product Identification mode.
Byte 0 (A0=V
IL
) represents the manufacturer code, and
byte 1 (A0=V
IH
), the device code. For HT27LC020,
these two identifier bytes are given in the Mode Select
Table. All identifiers for the manufacturer and device
codes will possess odd parity, with the MSB (DQ7) de-
fined as the parity bit. When A1=V
IL
, the HT27LC020
will read out the binary code of 7F, continuation code, to
signify the unavailability of manufacturer ID codes.
相關PDF資料
PDF描述
HT27LC040 CMOS 512K 8-Bit OTP EPROM
HT27LC512 OTP CMOS 64Kx 8-Bit EPROM
HT2812 Single Sound Generator
HT2812-14DIP Single Sound Generator
HT2812-8DIP Single Sound Generator
相關代理商/技術參數
參數描述
HT27LC020-32DIP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM
HT27LC020-32PLCC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM
HT27LC020-32SOP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM
HT27LC040 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CMOS 512K 8-Bit OTP EPROM
HT27LC4096 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS 256K?16-Bit OTP EPROM ??(3.3V)