- 您現(xiàn)在的位置：買賣IC網 > PDF目錄385394 > HSDL-3603-208 (Avago Technologies Ltd.) IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver PDF資料下載
參數資料
| 型號： | HSDL-3603-208 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver |
| 中文描述： | 紅外線㈢數據符合4 Mbit / s的紅外收發(fā)器 |
| 文件頁數： | 21/29頁 |
| 文件大?。?/td> | 226K |
| 代理商： | HSDL-3603-208 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
21
Appendix C: PCB Layout Suggestion
The following PCB layout guide-
lines should be followed to obtain a
good PSRR and EM immunity,
resulting in good electrical
performance. Things to note:
1. The AGND pin should be
connected to the ground plane.
2. C1 and C2 are optional supply
filter capacitors; they may be left
out if a clean power supply is
used.
3. VLED can be connected to either
unfiltered or unregulated power
supply. If VLED and V
CC
share
the same power supply and C1 is
used, the connection should be
before the current limiting
resistor R1. In a noisy environ-
ment, including capacitor C2 can
enhance supply rejection. C1 is
generally a ceramic capacitor of
low inductance providing a wide
frequency response while C2 is a
tantalum capacitor of big volume
and fast frequency response. The
use of a tantalum capacitor is
more critical on the V
LED
line,
which carries a high current.
4. Preferably, a multi-layered board
should be used to provide
sufficient ground plane. Use the
layer underneath and near the
transceiver module as V
CC
, and
sandwich that layer between
ground connected board layers.
Refer to the diagram below for
an example of a 4-layer board.
TOP LAYER
CONNECT THE METAL SHIELD AND MODULE
GROUND PIN TO BOTTOM GROUND LAYER.
LAYER 2
CRITICAL GROUND PLANE ZONE. DO NOT
CONNECT DIRECTLY TO THE MODULE
GROUND PIN.
LAYER 3
KEEP DATA BUS AWAY FROM CRITICAL
GROUND PLANE ZONE.
BOTTOM LAYER (GND)
The area underneath the module at
the second layer, and 3 cm in all
directions around the module, is
defined as the critical ground plane
zone. The ground plane should be
maximized in this zone. Refer to
application note AN1114 or the
Avago IrDA Data Link Design
Guide
for details. The layout below
is based on a 2-layer PCB.
28 mm
Top Layer
Figure 26. PCB layout suggestion.
Bottom Layer
17.2 mm
相關PDF資料 |
PDF描述 |
|---|---|
| HSDL-4250 | High-Performance T-1 (5mm) AlGaAs Infrared (870nm) Lamp |
| HSDL-4251 | High-Performance T-1 (5mm) AlGaAs Infrared (870nm) Lamp |
| HSDL-4260 | High-Power T-1 (5mm) AlGaAs Infrared (875nm) Lamp |
| HSDL-4261 | High-Power T-1 (5mm) AlGaAs Infrared (870nm) Lamp |
| HSDL-4270 | High-Performance T-1 (5mm) AlGaAs Infrared (940nm) Lamp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSDL-3610 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IrDA 1.0 Data Compliant 115.2Kb/s 3-5V Infrared Transceiver(not recommended for new designs) |
| HSDL-3610#007 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HSDL-3610#008 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HSDL-3610#017 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HSDL-3610#018 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
發(fā)布緊急采購，3分鐘左右您將得到回復。