- 您現在的位置：買賣IC網 > PDF目錄367211 > HMC392 (美國訊泰微波有限公司上海代表處) GaAs MMIC LOW NOISE AMPLIFIER, 3.5 - 7.0 GHz PDF資料下載
參數資料
| 型號： | HMC392 |
| 廠商： | 美國訊泰微波有限公司上海代表處 |
| 英文描述： | GaAs MMIC LOW NOISE AMPLIFIER, 3.5 - 7.0 GHz |
| 中文描述： | 砷化鎵MMIC低噪聲放大器，3.5 - 7.0吉赫 |
| 文件頁數： | 6/6頁 |
| 文件大?。?/td> | 228K |
| 代理商： | HMC392 |
MICROWAVE CORPORATION
1 - 35
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
A
1
HMC392
v00.1002
Assembly Diagram
Note: State 5 shown. PS3 and PS7 bonded to ground.
GaAs MMIC LOW NOISE
AMPLIFIER, 3.5 - 7.0 GHz
Handling Precautions
Follow these precautions to avoid permanent damage.
Cleanliness:
Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems.
Static Sensitivity:
Follow ESD precautions to protect against > ± 250V ESD strikes.
Transients:
Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize
inductive pick-up.
General Handling:
Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the
chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting
surface should be clean and flat.
Eutectic Die Attach:
A 80/20 gold tin preform is recommended with a work surface temperature of 255 deg. C and a tool temperature
of 265 deg. C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 deg. C. DO NOT expose the chip
to a temperature greater than 320 deg. C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for
attachment.
Epoxy Die Attach:
Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of
150 deg. C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum
level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or
substrate. All bonds should be as short as possible <0.31mm (12 mils).
相關PDF資料 |
PDF描述 |
|---|---|
| HMC393MS8G | GaAs MMIC DPDT DIVERSITY SWITCH, 5.0 - 6.0 GHz |
| HMC394LP4 | GaAs HBT PROGRAMMABLE 5-BIT COUNTER, DC - 2.2 GHz |
| HMC395 | InGaP HBT GAIN BLOCK MMIC AMPLIFIER, DC - 4.0 GHz |
| HMC396 | 600000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| HMC397 | 600,000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC392_09 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC LOW NOISE AMPLIFIER, 3.5 - 7.0 GHz |
| HMC392ALC4TR | 功能描述:IC MMIC LNA GAAS 24SMD 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:在售 頻率:1.7GHz ~ 2.7GHz P1dB:12dBm 增益:9dB 噪聲系數:12.5dB RF 類型:CDMA，GSM，EDGE，W-CDMA 電壓 - 電源:5V 電流 - 電源:260mA 測試頻率:2.7GHz 封裝/外殼:24-TFCQFN 裸露焊盤 供應商器件封裝:24-LCC（4x4） 標準包裝:1 |
| HMC392LC4 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC LOW NOISE AMPLIFIER, 3.5 - 7.0 GHz |
| HMC392LC4_09 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC LOW NOISE AMPLIFIER, 3.5 - 7.0 GHz |
| HMC392LC4TR | 制造商:Hittite Microwave Corp 功能描述:Low Noise Amplifier SMT, 3.5 - 7.0 GHz |
發布緊急采購，3分鐘左右您將得到回復。