- 您現在的位置：買賣IC網 > PDF目錄367208 > HMC292 (美國訊泰微波有限公司上海代表處) 600000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN PDF資料下載
參數資料
| 型號： | HMC292 |
| 廠商： | 美國訊泰微波有限公司上海代表處 |
| 元件分類： | FPGA |
| 英文描述： | 600000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| 中文描述： | GaAs MMIC雙平衡混頻器，18 - 32千兆赫 |
| 文件頁數： | 6/6頁 |
| 文件大小： | 167K |
| 代理商： | HMC292 |
MICROWAVE CORPORATION
5 - 75
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
M
5
Handling Precautions
Follow these precautions to avoid permanent damage.
HMC292
GaAs MMIC DOUBLE-BALANCED
MIXER, 18 - 32 GHz
v02.1202
Cleanliness:
Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems.
Static Sensitivity:
Follow ESD precautions to protect against > ± 250V ESD strikes.
Transients:
Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize
inductive pick-up.
General Handling:
Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the
chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting
surface should be clean and flat.
Eutectic Die Attach:
A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature
of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip
to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for
attachment.
Epoxy Die Attach:
Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded with a force of 40-
60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds should be made with
a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a nominal stage temperature of 150 °C. A
minimum amount of ultrasonic energy should be applied to achieve reliable bonds. All bonds should be as short as possible, less than
12 mils (0.31 mm).
相關PDF資料 |
PDF描述 |
|---|---|
| HMC294 | GaAs MMIC DOUBLE-BALANCED MIXER, 25 - 40 GHz |
| HMC296MS8 | LOW LO DRIVE DOUBLE-BALANCED FET MIXER, 1.1 - 1.7 GHz |
| HMC300LM1 | SMT MEDIUM POWER GaAs MMIC AMPLIFIER, 25.5 - 33.5 GHz |
| HMC304MS8 | GaAs MMIC HIGH IP3 SINGLEBALANCED SMT MIXER, 1.7 - 3 GHz |
| HMC305LP4 | 0.5 dB LSB GaAs MMIC 5-BIT SERIAL CONTROL DIGITAL ATTENUATOR, 0.7 - 3.8 GHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC292_08 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC DOUBLE-BALANCED MIXER, 18 - 32 GHz |
| HMC292_09 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC DOUBLE-BALANCED MIXER, 18 - 32 GHz |
| HMC292ALC3B | 功能描述:IC MMIC MIXER HI IP3 12-QFN 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:在售 RF 類型:- 頻率:18GHz ~ 32GHz 混頻器數:1 增益:- 噪聲系數:9dB 輔助屬性:- 電流 - 電源:- 電壓 - 電源:- 封裝/外殼:12-CLCC 裸露焊盤 供應商器件封裝:12-CLCC（2.9x2.9） 標準包裝:1 |
| HMC292LC3B | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC FUNDAMENTAL MIXER, 16 - 30 GHz |
| HMC292LC3B_09 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC FUNDAMENTAL MIXER, 16 - 30 GHz |
發布緊急采購，3分鐘左右您將得到回復。