- 您現在的位置：買賣IC網 > PDF目錄384423 > HIP9011ABZ (INTERSIL CORP) Engine Knock Signal Processor PDF資料下載
參數資料
| 型號： | HIP9011ABZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Engine Knock Signal Processor |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | LEAD FREEE, PLASTIC, MS-013-AC, SOIC-20 |
| 文件頁數： | 2/11頁 |
| 文件大小： | 253K |
| 代理商： | HIP9011ABZ |
2
FN4367.2
January 6, 2006
Pinout
HIP9011
(SOIC)
TOP VIEW
11
12
13
14
15
16
17
18
20
19
10
9
8
7
6
5
4
3
2
1
V
DD
VMID
INTOUT
INT/HOLD
CS
SO
SI
SCK
TEST
CH1IN
CH1FB
CH0FB
CH0IN
GND
NC
NC
OSCIN
OSCOUT
CH0NI
CH1NI
Pin Descriptions
PIN
NUMBER
DESIGNATION
DESCRIPTION
1
V
DD
Five volt power input.
2
GND
This pin is tied to ground.
3
V
MID
This pin is connected to the internal mid-supply generator and is brought out for bypassing by a 0.022
μ
F capacitor.
4
INTOUT
Buffered output of the integrator. Output signal is held by an internal Sample and Hold circuit when INT/HOLD is
low.
5, 6
NC
These pins are not internally connected. Do Not Use.
7
INT/HOLD
Selects whether the chip is in the Integrate Mode (Input High) or in the Hold Mode (Input Low). This pin has an
internal pull down.
8
CS
A low input on this pin enables the chip to communicate over the SPI bus. This pin has an internal pull-up.
9
OSCIN
Input to inverter used for the oscillator circuit. A 4MHz crystal or ceramic resonator is connected between this pin and
pin 10. To bias the inverter, a 1.0M
to 10M
resistor is usually connected between this pin and pin 10.
10
OSCOUT
Output of the inverter used for the oscillator. See pin 9 above.
11
SO
Output of the chip SPI data bus. This is a three-state output that is controlled via the SPI bus. The output is
placed in the high impedance state by setting CS high when the chip is not selected. This high impedance state
can also be programmed by setting the LSB of the prescaler word to 1. This will take precedence over CS. A 0
enables the active state. The Diagnostic Mode overrides these conditions.
12
SI
Input of the chip SPI data bus. Data length is eight bits. This pin has an internal pull-up.
13
SCK
Input from the SPI clock. Normally low, the data is transferred to the chip internal circuitry on the falling clock
edge. This pin has an internal pull up.
14
TEST
A low on this pin places the chip in the diagnostic mode. For normal operation this pin is tied high or left open.
This pin has an internal pull up.
15
CH1NI
Non-inverting input of Channel one.
16
CH1IN
Inverting input to channel one amplifier. A resistor is tied from this summing input to the transducer. A second
resistor is tied between this pin and pin 17, CH1FB to establish the gain of the amplifier.
17
CH1FB
Output of the channel one amplifier. This pin is used to apply feedback.
18
CH0FB
Output of the channel zero amplifier. This pin is used to apply feedback.
19
CH0IN
Inverting input to channel zero amplifier. Remainder same as channel one amplifier except feedback is applied
from pin 18.
20
CH0NI
Non-inverting input of Channel 0. Remainder the same as pin 16, except feedback is applied from terminal 18.
HIP9011
相關PDF資料 |
PDF描述 |
|---|---|
| HIP9011 | Engine Knock Signal Processor |
| HIP9011AB | Engine Knock Signal Processor |
| HIP9020 | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AB | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AP | Programmable Quad Buffer with Pre and Post Scaler Dividers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP9011ABZT | 功能描述:接口 - 專用 W/ANNEAL KNOCK SENSOR TAPE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| HIP9011ABZTR5133 | 制造商:Intersil Corporation 功能描述:PB-FREE VISTEON HIP9011ABZT W/BARCODE LABELS,PB DIE,ELECT SE - Tape and Reel 制造商:Intersil Corporation 功能描述:ITSHIP9011ABZTR5133 W/BARCODE LABELS,PB |
| HIP9011EVAL1Z | 功能描述:電源管理IC開發工具 HIP9011 EVAL BRD 1 ROHS CMPL RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HIP9020 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。