參數資料
型號： HI7190IP
廠商： Intersil
文件頁數： 6/25頁
文件大小： 0K
描述： IC ADC 24BIT PROGBL SER 20-PDIP
標準包裝： 18
位數： 24
數據接口： 串行，SPI?
轉換器數目： 1
功率耗散（最大）： 32.5mW
電壓電源： 模擬和數字，雙 ±
工作溫度： -40°C ~ 85°C
安裝類型： 通孔
封裝/外殼： 20-DIP（0.300"，7.62mm）
供應商設備封裝： 20-PDIP
包裝： 管件
輸入數目和類型： 1 個差分，單極；1 個差分，雙極
14
FN3612.10
June 27, 2006
The HI7190 offers several different modes of Self-Calibration
and System Calibration. For calibration to occur, the on-chip
microcontroller must convert the modulator output for three
different input conditions - “zero-scale,” “positive full scale,”
and “negative full scale”. With these readings, the HI7190
can null any offset errors and calculate the gain slope factor
for the transfer function of the converter. It is imperative that
the zero-scale calibration be performed before either of the
gain calibrations. However, the order of the gain calibrations
is not important.
The calibration modes are user selectable in the Control
Register by using the MD bits (MD2-MD0) as shown in
Table 4. DRDY will go low indicating that the calibration is
complete and there is valid data at the output.
Conversion Mode
For Conversion Mode operation the HI7190 converts the
differential voltage between VINHI and VINLO . From
switching into this mode it takes 3 conversion periods (3 x
1/fN) for DRDY to go low and new data to be valid. No
calibration coefficients are generated when operating in
Conversion Mode as data is calibrated using the existing
calibration coefficients.
Self-Calibration Mode
Please note: Self-calibration is only valid when operating in a
gain of one. In addition, the offset and gain errors are not
reduced as with the full system calibration.
The Self-Calibration Mode is a three step process that
updates the Offset Calibration Register, the Positive Full
Scale Calibration Register, and the Negative Full Scale
Calibration Register. In this mode an internal offset
calibration is done by disconnecting the external inputs and
shorting the inputs of the PGIA together. After 3 conversion
periods the Offset Calibration Register is updated with the
value that corrects any internal offset errors.
After the offset calibration is completed, the Positive and
Negative Full Scale Calibration Registers are updated. The
inputs VINHI and VINLO are disconnected and the external
reference is applied across the modulator inputs. The
HI7190 then takes 3 conversion cycles to sample the data
and update the Positive Full Scale Calibration Register. Next
the polarity of the reference voltage across the modulator
input terminals is reversed and after 3 conversion cycles the
Negative Full Scale Calibration Register is updated. The
values stored in the Positive and Negative Full Scale
Calibration Registers correct for any internal gain errors in
the A/D transfer function. After 3 more conversion cycles the
DRDY line will activate signaling that the calibration is
complete and valid data is present in the Data Output
Register.
System Offset Calibration Mode
The System Offset Calibration Mode is a single step process
that allows the user to lump offset errors of external circuitry
and the internal errors of the HI7190 together and null them
out. This mode will convert the external differential signal
applied to the VIN inputs and then store that value in the
Offset Calibration Register. The user must apply the zero
point or offset voltage to the HI7190 analog inputs and allow
the signal to settle before selecting this mode. After 4
conversion periods the DRDY line will activate signaling that
the calibration is complete and valid data is present in the
Data Output Register.
System Positive Full Scale Calibration Mode
The System Positive Full Scale Calibration Mode is a single
step process that allows the user to lump gain errors of
external circuitry and the internal errors of the HI7190
together and null them out. This mode will convert the
external differential signal applied to the VIN inputs and
stores the converted value in the Positive Full Scale
Calibration Register. The user must apply the +Full Scale
voltage to the HI7190 analog inputs and allow the signal to
settle before selecting this mode. After 4 conversion periods
the DRDY line will activate signaling the calibration is
complete and valid data is present in the Data Output
Register.
System Negative Full Scale Calibration Mode
The System Negative Full Scale Calibration Mode is a
single-step process that allows the user to lump gain errors
of external circuitry and the internal errors of the HI7190
together and null them out. This mode will convert the
external differential signal applied to the VIN inputs and
stores the converted value in the Negative Full Scale
Calibration Register. The user must apply the -Full Scale
voltage to the HI7190 analog inputs and allow the signal to
settle before selecting this mode. After 4 conversion periods
the DRDY line will activate signaling the calibration is
complete and valid data is present in the Data Output
Register.
TABLE 4. HI7190 OPERATIONAL MODES
MD2
MD1
MD0
OPERATIONAL MODE
0
Conversion
0
1
Self Calibration (Gain of 1 only)
0
1
0
System Offset Calibration
0
1
System Positive Full Scale Calibration
1
0
System Negative Full Scale Calibration
1
0
1
System Offset/Internal Gain Calibration
(Gain of 1 only)
1
0
System Gain Calibration
111
Reserved
HI7190
相關PDF資料
PDF描述
HI7191IP IC ADC 24BIT PROGBL SER 20-PDIP
HI9P5701K-5 CONV A/D 6BIT 30MSPS 18-SOIC
HMC700LP4E IC FRACT-N PLL 16BIT 24QFN
HMC703LP4E IC FRACT-N PLL W/SWEEPR 24QFN
HMC704LP4E IC FRACT-N PLL 16BIT 24QFN
相關代理商/技術參數
參數描述
HI7190IPZ 功能描述:模數轉換器 - ADC W/ANNEAL ADC 24BIT 1 0HZ SIGMADELTA RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
HI7191 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:24-Bit, High Precision, Sigma Delta A/D Converter
HI7191_06 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:24-Bit, High Precision, Sigma Delta A/D Converter
HI7191IB 功能描述:IC ADC 24BIT PROGBL SER 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
HI7191IBZ 功能描述:模數轉換器 - ADC ADC 24BIT SIGMADELTA 20 IND RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*