- 您現在的位置：買賣IC網 > PDF目錄385380 > HI3-0539-5 (HARRIS SEMICONDUCTOR) RESISTOR POWER 150 OHM 8W 5% PDF資料下載
參數資料
| 型號： | HI3-0539-5 |
| 廠商： | HARRIS SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | RESISTOR POWER 150 OHM 8W 5% |
| 中文描述： | 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, PDIP16 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 189K |
| 代理商： | HI3-0539-5 |
8
Application Information
General
The Hl-539 accepts inputs in the range -15V to +15V, with
performance guaranteed over the
±
10V range. At these
higher levels of analog input voltage it is comparable to the Hl-
509, and is plug-in compatible with that device (as well as the
Hl-509A). However, as mentioned earlier, the Hl-539 was
designed to introduce minimum error when switching low level
inputs.
Special care is required in working with these low level
signals. The main concern with signals below 100mV is that
noise, offset voltage, and other aberrations can represent a
large percentage error. A shielded differential signal path is
essential to maintain a noise level below 50
μ
V
RMS
.
Low Level Signal Transmission
The transmission cable carrying the transducer signal is critical
in a low level system. It should be as short as practical and
rigidly supported. Signal conductors should be tightly twisted
for minimum enclosed area to guard against pickup of
electromagnetic interference, and the twisted pair should be
shielded against capacitively coupled (electrostatic)
interference. A braided wire shield may be satisfactory, but a
lapped foil shield is better since it allows only
1
/
10
as much
leakage capacitance to ground per foot. A key requirement for
the transmission cable is that it presents a balanced line to
sources of noise interference. This means an equal series
impedance in each conductor plus an equally distributed
impedance from each conductor to ground. The result should
be signals equal in magnitude but opposite in phase at any
transverse plane. Noise will be coupled in phase to both
conductors, and may be rejected as common-mode voltage by
a differential amplifier connected to the multiplexer output.
Coaxial cable is not suitable for low level signals because the
two conductors (center and shield) are unbalanced. Also,
ground loops are produced if the shield is grounded at both
ends by standard BNC connectors. If coax must be used, carry
the signal on the center conductors of two equal-length cables
whose shields are terminated only at the transducer end. As a
general rule, terminate (ground) the shield at one end only,
preferably at the end with greatest noise interference. This is
usually the transducer end for both high and low level signals.
Watch Small
V Errors
Printed circuit traces and short lengths of wire can add
substantial error to a signal even after it has traveled
hundreds of feet and arrived on a circuit board. Here, the
small voltage drops due to current flow through connections
of a few milliohms must be considered, especially to meet an
accuracy requirement of 12 bits or more.
Table 1 is a useful collection of data for calculating the effect
of these short connections. (Proximity to a ground plane will
lower the values of inductance.)
As an example, suppose the Hl-539 is feeding a 12-bit
converter system with an allowable error of
±
1
/
2
LSB
(
±
1.22mV). lf the interface logic draws 100mA from the 5V
supply, this current will produce 1.28mV across 6 inches of
#24 wire; more than the error budget. Obviously, this digital
current must not be routed through any portion of the analog
ground return network.
FIGURE 7A. SINGLE-ENDED CROSSTALK TEST CIRCUIT
FIGURE 7B. DIFFERENTIAL CROSSTALK TEST CIRCUIT
FIGURE 7. CROSSTALK
Test Circuits and Waveforms
Unless Otherwise Specified T
A
= 25
o
C, V+ = +15V, V- = -15V, V
AH
= 4V and V
AL
= 0.8V
(Continued)
HI-539
INSTRUMENTATION
AMPLIFIER
AD606 or BB3630, for Example
+
-
G = 1000
350
1kHz,
15V
P-P
AD606 or BB3630, for example
HI-539
INSTRUMENTATION
AMPLIFIER
+
-
G = 1000
350
1kHz,
15V
P-P
350
HI-539
相關PDF資料 |
PDF描述 |
|---|---|
| HI4P0539-5 | Precision, 4-Channel, Low-Level, Differential Multiplexer |
| HI1-0539-5 | Precision, 4-Channel, Low-Level, Differential Multiplexer |
| HI1-0539-8 | Precision, 4-Channel, Low-Level, Differential Multiplexer |
| HI-539 | Precision, 4-Channel, Low-Level, Differential Multiplexer |
| HI3-0546-5 | Single 16 and 8, Differential 8-Channel and 4-Channel CMOS Analog MUXs with Active Overvoltage Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI3-0546-5 | 功能描述:IC MULTIPLEXER 16X1 28DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| HI3-0546-5Z | 功能描述:多路器開關 IC MUX 16:1 OVP COM RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| HI3-0546-9 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI3-0547-5 | 功能描述:IC MULTIPLEXER DUAL 8X1 28DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| HI3-0547-5Z | 功能描述:多路器開關 IC MUX DIFF 8:1 OVP COM RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。