- 您現在的位置：買賣IC網 > PDF目錄385375 > HFA1113 (Intersil Corporation) 850MHz, Low Distortion, Output Limiting, Programmable Gain, Buffer Amplifier(850MHz、低失真、輸出限定可編程增益緩沖放大器) PDF資料下載
參數資料
| 型號： | HFA1113 |
| 廠商： | Intersil Corporation |
| 英文描述： | 850MHz, Low Distortion, Output Limiting, Programmable Gain, Buffer Amplifier(850MHz、低失真、輸出限定可編程增益緩沖放大器) |
| 中文描述： | 是850MHz，低失真，輸出限制，可編程增益，緩沖放大器（是850MHz，低失真，輸出限定可編程增益緩沖放大器） |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 491K |
| 代理商： | HFA1113 |
7
FN1342.6
July 11, 2005
Clamp Accuracy
The clamped output voltage will not be exactly equal to the
voltage applied to V
H
or V
L
. Offset errors, mostly due to V
BE
mismatches, necessitate a clamp accuracy parameter which
is found in the device specifications. Clamp accuracy is a
function of the clamping conditions. Referring again to
Figure 4, it can be seen that one component of clamp
accuracy is the VBE mismatch between the Q
X6
transistors,
and the Q
X5
transistors. If the transistors always ran at the
same current level there would be no V
BE
mismatch, and no
contribution to the inaccuracy. The Q
X6
transistors are
biased at a constant current, but as described earlier, the
current through Q
X5
is equivalent to I
CLAMP
. V
BE
increases
as I
CLAMP
increases, causing the clamped output voltage to
increase as well. I
CLAMP
is a function of the overdrive level
(A
VCL
x V
IN
- V
OUT
CLAMPED
), so clamp accuracy degrades
as the overdrive increases. As an example, the specified
accuracy of
±
100mV (A
V
= -1, V
H
= 1V) for a 1.6X overdrive
degrades to
±
240mV for a 3X (200%) overdrive, as shown in
Figure 43.
Consideration must also be given to the fact that the clamp
voltages have an affect on amplifier linearity. The
“Nonlinearity Near Clamp Voltage” curve, Figure 48,
illustrates the impact of several clamp levels on linearity.
Clamp Range
Unlike some competitor devices, both V
H
and V
L
have
usable ranges that cross 0V. While V
H
must be more positive
than V
L
, both may be positive or negative, within the range
restrictions indicated in the specifications. For example, the
HFA1113 could be limited to ECL output levels by setting
V
H
= -0.8V and V
L
= -1.8V. V
H
and V
L
may be connected to
the same voltage (GND for instance) but the result won’t be
in a DC output voltage from an AC input signal. A
150mV - 200mV AC signal will still be present at the output.
Recovery from Overdrive
The output voltage remains at the clamp level as long as the
overdrive condition remains. When the input voltage drops
below the overdrive level (V
CLAMP
/A
VCL
) the amplifier will
return to linear operation. A time delay, known as the
Overdrive Recovery Time, is required for this resumption of
linear operation. The plots of “Unclamped Performance” and
“Clamped Performance” (Figures 41 and 42) highlight the
HFA1113’s subnanosecond recovery time. The difference
between the unclamped and clamped propagation delays is
the overdrive recovery time. The appropriate propagation
delays are 8.0ns for the unclamped pulse, and 8.8ns for the
clamped (2X overdrive) pulse yielding an overdrive recovery
time of 800ps. The measurement uses the 90% point of the
output transition to ensure that linear operation has
resumed. Note: The propagation delay illustrated is
dominated by the fixturing. The delta shown is accurate, but
the true HFA1113 propagation delay is 500ps.
Overdrive recovery time is also a function of the overdrive
level. Figure 47 details the overdrive recovery time for
various clamp and overdrive levels.
Typical Performance Curves
V
SUPPLY
=
±
5V, T
A
= 25
o
C, R
L
= 100
, Unless Otherwise Specified
FIGURE 5. SMALL SIGNAL PULSE RESPONSE
FIGURE 6. LARGE SIGNAL PULSE RESPONSE
A
V
= +2
200
150
100
50
0
-50
-100
-150
-200
O
TIME (5ns/DIV.)
A
V
= +2
2.0
1.5
1.0
0.5
0
-0.5
-1.0
-1.5
-2.0
O
TIME (5ns/DIV.)
HFA1113
相關PDF資料 |
PDF描述 |
|---|---|
| HFA1115883 | High Speed, Low Power, Output Limiting Closed Loop Buffer Amplifier |
| HFA1115IP | Mini-Stripax Plus Replacement Blade; Conductor Size AWG:24-22; Features:Includes top & bottom blades, spring & wire stop; Specially formed stripping blades ensure no damage to the conductor; Easy to install RoHS Compliant: Yes |
| HFA1115IB | SINGLEMODE FIBER PATCH CABLE, PLENUM SC-LC 10M |
| HFA1115EVAL | 225MHz, Low Power, Output Limiting, Closed Loop Buffer Amplifier |
| HFA1115 | 225MHz, Low Power, Output Limiting, Closed Loop Buffer Amplifier(225MHz、低功耗、輸出限定鎖相環緩沖器放大器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFA1113/883 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Output Limiting, Ultra High Speed Programmable Gain, Buffer Amplifier |
| HFA1113_05 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:850MHz, Low Distortion, Output Limiting, Programmable Gain, Buffer Amplifier |
| HFA1113883 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Output Limiting, Ultra High Speed Programmable Gain, Buffer Amplifier |
| HFA1113EVAL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:850MHz, Low Distortion, Output Limiting, Programmable Gain, Buffer Amplifier |
| HFA1113IB | 功能描述:IC BUFFER 850MHZ 8-SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
發布緊急采購，3分鐘左右您將得到回復。