- 您現在的位置：買賣IC網 > PDF目錄385375 > HFA1113 (Intersil Corporation) 850MHz, Low Distortion, Output Limiting, Programmable Gain, Buffer Amplifier(850MHz、低失真、輸出限定可編程增益緩沖放大器) PDF資料下載
參數資料
| 型號： | HFA1113 |
| 廠商： | Intersil Corporation |
| 英文描述： | 850MHz, Low Distortion, Output Limiting, Programmable Gain, Buffer Amplifier(850MHz、低失真、輸出限定可編程增益緩沖放大器) |
| 中文描述： | 是850MHz，低失真，輸出限制，可編程增益，緩沖放大器（是850MHz，低失真，輸出限定可編程增益緩沖放大器） |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 491K |
| 代理商： | HFA1113 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
5
FN1342.6
July 11, 2005
Application Information
Closed Loop Gain Selection
The HFA1113 features a novel design which allows the user
to select from three closed loop gains, without any external
components. The result is a more flexible product, fewer part
types in inventory, and more efficient use of board space.
This “buffer” operates in closed loop gains of -1, +1, or +2,
and gain selection is accomplished via connections to the
±
Inputs. Applying the input signal to +IN and floating -IN
selects a gain of +1, while grounding -IN selects a gain of
+2. A gain of -1 is obtained by applying the input signal to
-IN with +IN grounded.
The table below summarizes these connections:
PC Board Layout
The frequency response of this amplifier depends greatly on
the amount of care taken in designing the PC board.
The
use of low inductance components such as chip
resistors and chip capacitors is strongly recommended,
while a solid ground plane is a must!
Attention should be given to decoupling the power supplies.
A large value (10
μ
F) tantalum in parallel with a small value
chip (0.1
μ
F) capacitor works well in most cases.
Terminated microstrip signal lines are recommended at the
input and output of the device. Capacitance directly on the
output must be minimized, or isolated as discussed in the
next section.
For unity gain applications, care must also be taken to
minimize the capacitance to ground seen by the amplifier’s
inverting input. At higher frequencies this capacitance will
tend to short the -INPUT to GND, resulting in a closed loop
gain which increases with frequency. This will cause
excessive high frequency peaking and potentially other
problems as well.
An example of a good high frequency layout is the
Evaluation Board shown in Figure 3.
Driving Capacitive Loads
Capacitive loads, such as an A/D input, or an improperly
terminated transmission line will degrade the amplifier’s
phase margin resulting in frequency response peaking and
possible oscillations. In most cases, the oscillation can be
avoided by placing a resistor (R
S
) in series with the output
prior to the capacitance.
Figure 1 details starting points for the selection of this
resistor. The points on the curve indicate the R
S
and C
L
combinations for the optimum bandwidth, stability, and
settling time, but experimental fine tuning is recommended.
Picking a point above or to the right of the curve yields an
overdamped response, while points below or left of the curve
indicate areas of underdamped performance.
R
S
and C
L
form a low pass network at the output, thus
limiting system bandwidth well below the amplifier bandwidth
of 850MHz. By decreasing R
S
as C
L
increases (as illustrated
in the curves), the maximum bandwidth is obtained without
sacrificing stability. Even so, bandwidth does decrease as
you move to the right along the curve. For example, at
A
V
= +1, R
S
= 50
, C
L
= 30pF, the overall bandwidth is
limited to 300MHz, and bandwidth drops to 100MHz at
A
V
= +1, R
S
= 5
, C
L
= 340pF.
Evaluation Board
The performance of the HFA1113 may be evaluated using
the HFA11XX Evaluation Board, slightly modified as follows:
1. Remove the 500
feedback resistor (R
2
), and leave the
connection open.
2. a. For A
V
= +1 evaluation, remove the 500
gain setting
resistor (R
1
), and leave pin 2 floating.
b. For A
V
= +2, replace the 500
gain setting resistor with
a 0
resistor to GND.
The modified schematic and layout of the board are shown in
Figures 2 and 3.
To order evaluation boards (part number HFA11XXEVAL),
please contact your local sales office.
NOTE: The SOIC version may be evaluated in the DIP board by
using a SOIC-to-DIP adapter such as Aries Electronics Part Number
08-350000-10.
GAIN (A
CL
)
CONNECTIONS
+INPUT
(PIN 3)
-INPUT
(PIN 2)
-1
GND
Input
+1
Input
NC (Floating)
+2
Input
GND
R
S
)
LOAD CAPACITANCE (pF)
50
45
40
35
30
25
20
15
10
5
0
0
40
80
120
160
200
240
280
320
360
400
A
V
= +1
A
V
= +2
FIGURE 1. RECOMMENDED SERIES RESISTOR vs LOAD
CAPACITANCE
HFA1113
相關PDF資料 |
PDF描述 |
|---|---|
| HFA1115883 | High Speed, Low Power, Output Limiting Closed Loop Buffer Amplifier |
| HFA1115IP | Mini-Stripax Plus Replacement Blade; Conductor Size AWG:24-22; Features:Includes top & bottom blades, spring & wire stop; Specially formed stripping blades ensure no damage to the conductor; Easy to install RoHS Compliant: Yes |
| HFA1115IB | SINGLEMODE FIBER PATCH CABLE, PLENUM SC-LC 10M |
| HFA1115EVAL | 225MHz, Low Power, Output Limiting, Closed Loop Buffer Amplifier |
| HFA1115 | 225MHz, Low Power, Output Limiting, Closed Loop Buffer Amplifier(225MHz、低功耗、輸出限定鎖相環緩沖器放大器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFA1113/883 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Output Limiting, Ultra High Speed Programmable Gain, Buffer Amplifier |
| HFA1113_05 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:850MHz, Low Distortion, Output Limiting, Programmable Gain, Buffer Amplifier |
| HFA1113883 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Output Limiting, Ultra High Speed Programmable Gain, Buffer Amplifier |
| HFA1113EVAL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:850MHz, Low Distortion, Output Limiting, Programmable Gain, Buffer Amplifier |
| HFA1113IB | 功能描述:IC BUFFER 850MHZ 8-SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
發布緊急采購，3分鐘左右您將得到回復。