- 您現在的位置：買賣IC網 > PDF目錄384393 > HC5517CB (HARRIS SEMICONDUCTOR) 3 REN Ringing SLIC For ISDN Modem/TA and WLL PDF資料下載
參數資料
| 型號： | HC5517CB |
| 廠商： | HARRIS SEMICONDUCTOR |
| 元件分類： | 模擬傳輸電路 |
| 英文描述： | 3 REN Ringing SLIC For ISDN Modem/TA and WLL |
| 中文描述： | TELECOM-SLIC, PDSO28 |
| 文件頁數： | 16/18頁 |
| 文件大?。?/td> | 175K |
| 代理商： | HC5517CB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁
75
The part has two ground pins, one is labeled AGND and the
other BGND. Both pins should be connected together as
close as possible to the SLIC. If a ground plane is available,
then both AGND and BGND should be connected directly to
the ground plane.
A ground plane that provides a low impedance return path
for the supply currents should be used. A ground plane
provides isolation between analog and digital signals. If the
layout density does not accommodate a ground plane, a
single point grounding scheme should be used.
Application Pin Descriptions
PLCC
SYMBOL
DESCRIPTION
1
AGND
Analog Ground - To be connected to zero potential. Serves as a reference for the transmit output and receive input
terminals.
2
V
CC
V
REF
F1
Positive Voltage Source - Most Positive Supply.
3
Ring amplifier reference override. An external voltage connected to this pin will override the internal V
BAT
/2 reference.
Power Denial -A low active TTL compatible logic control input. When enabled, the output of the ring amplifier will ramp
close to the output voltage of the tip amplifier.
4
5
F0
TTL compatible logic control input that must be tied high for proper SLIC operation.
6
RS
TTL compatible logic control input that must be tied high for proper SLIC operation.
7
SHD
Switch Hook Detection - An active low TTL compatible logic output. Indicates an offhook condition.
8
RTD
Ring Trip Detection - An active low TTL compatible logic output. Indicates an off-hook condition when the phone is
ringing.
9
TST
A TTL logic input. A low on this pin will keep the SLIC in a power down mode. The TST pin in conjunction with the ALM pin
can provide thermal shutdown protection for the SLIC. Thermal shutdown is implemented by a system controller that
monitors the ALM pin. When the ALM pin is active (low) the system controller issues a command to the TST pin (low) to
power down the SLIC. The timing of the thermal recovery is controlled by the system controller.
10
ALM
A TTL compatible active low output which responds to the thermal detector circuit when a safe operating die
temperature has been exceeded.
11
I
LMT
OUT1
Loop Current Limit - Voltage on this pin sets the short loop current limiting conditions using a resistive voltage divider.
12
The analog output of the spare operational amplifier.
13
-IN1
The inverting analog input of the spare operational amplifier. Note that the non-inverting input of the amplifier is
internally connected to AGND.
14
TIP
SENSE
An analog input connected to the TIP (more positive) side of the subscriber loop through a feed resistor and ring relay
contact. Functions with the RING terminal to receive voice signals from the telephone and for loop monitoring
purpose.
15
RING SENSE 1
An analog input connected to the RING (more negative) side of the subscriber loop through a feed resistor. Functions
with the TIP terminal to receive voice signals from the telephone and for loop monitoring purposes.
16
RING SENSE 2
This is an internal sense mode that must be tied to RING SENSE 1 for proper SLIC operation.
17
V
RX
Receive Input, 4-Wire Side - A high impedance analog input. AC signals appearing at this input drive the Tip Feed
and Ring Feed amplifiers deferentially.
18
NU
Not used in this application.This pin should be left floating.
19
V
TX
Transmit Output, 4-Wire Side - A low impedance analog output which represents the differential voltage across TIP
and RING. Since the DC level of this output varies with loop current, capacitive coupling to the next stage is necessary.
20
RDI
TTL compatible input to drive the uncommitted relay driver.
21
RDO
This is the output of the uncommitted relay driver.
22
BGND
Battery Ground - To be connected to zero potential. All loop current and some quiescent current flows into this
terminal.
23
NU
Not used in this application. This pin should be either grounded or left floating.
24
V
RING
TF
Ring signal input (0V to 3V
PEAK
at 20Hz).
This is the output of the tip amplifier.
25
26
RF
This is the output of the ring amplifier.
27
V
BAT
RTI
The negative battery source.
28
Ring Trip Input - This pin is connected to the external negative peak detector output for ring trip detection.
HC5517
相關PDF資料 |
PDF描述 |
|---|---|
| HC5517CM | 3 REN Ringing SLIC For ISDN Modem/TA and WLL |
| HC5517IM | 3 REN Ringing SLIC For ISDN Modem/TA and WLL |
| HC5517IB | GIGATRUE 550 CAT PATCH CBL NO BOOT 6FT RD 25 PK |
| HC55180 | Extended Reach Ringing SLIC Family |
| HC55181 | Extended Reach Ringing SLIC Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HC5517CB96 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HC5517CM | 制造商:Harris Corporation 功能描述: |
| HC5517CM96 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HC5517IB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HC5517IM | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。