- 您現在的位置：買賣IC網 > PDF目錄10995 > HC55142IMZ96 (Intersil)IC SLIC UNIVERSAL LP 28-PLCC PDF資料下載
參數資料
| 型號： | HC55142IMZ96 |
| 廠商： | Intersil |
| 文件頁數： | 6/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SLIC UNIVERSAL LP 28-PLCC |
| 標準包裝： | 750 |
| 系列： | UniSLIC14 |
| 功能： | 用戶線路接口概念（SLIC） |
| 電路數： | 1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 電流 - 電源： | 2.25mA |
| 功率（瓦特）： | 1.5W |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-LCC（J 形引線） |
| 供應商設備封裝： | 28-PLCC（11.51x11.51） |
| 包裝： | 帶卷 (TR) |
| 包括： | 電池跟蹤抗削頂失真，回路和接地鍵檢測，振鈴控制 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
14
FN4659.13
June 1, 2006
23. Four-Wire to Two-Wire Gain Tracking - The 4-wire to 2-wire
gain tracking is referenced to measurements taken for
ERX = -10dBm, 1.0kHz signal, EG source removed from circuit,
RL = 600 and is computed using the following equation:
G4-2 = 20 log (VTR/ERX) vary amplitude -40dBm to +3dBm, or
-55dBm to -40dBm and compare to -10dBm reading.
VTR, RL and ERX are defined in Figure 8. The level is specified at
the 4-wire receive port and referenced to a 600
impedance level.
24. Two-Wire Idle Channel Noise - The 2-wire idle channel noise
at VTR is specified with the 2-wire port terminated in 600 (RL)
and with the 4-wire receive port (VTX) floating (Reference
Figure 9).
25. Four-Wire Idle Channel Noise - The 4-wire idle channel noise
at VTX is specified with the 2-wire port terminated in 600 (RL).
The noise specification is with respect to a 600
impedance
level at VTX. The 4-wire receive port (VTX) floating (Reference
Figure 9).
26. Harmonic Distortion (2-Wire to 4-Wire) - The harmonic
distortion is measured within the voice band with the following
conditions. EG = 0dBm at 1kHz, RL = 600. Measurement
taken at VTX. (Reference Figure 7).
27. Harmonic Distortion (4-Wire to 2-Wire) - The harmonic
distortion is measured within the voice band with the following
conditions. ERX = 0dBm0. Vary frequency between 300Hz and
3.4kHz, RL = 600. Measurement taken at VTR. (Reference
Figure 8).
28. Constant Loop Current - The constant loop current is
calculated using the following equation:
IL = 1000/RLIM = VTR/600 (Reference Figure 10).
29. Ground Key Detector - (TRIGGER) Ground the Ring pin
through a 2.5k
resistor and verify that GKD goes low.
(RESET) Disconnect the Ring pin and verify that GKD goes
high.
(Hysteresis) Compare difference between trigger and reset.
30. Electrical Test - Not tested in production at -40°C.
Circuit Operation and Design Information
The UniSLIC14 family of SLICs are voltage feed current
sense Subscriber Line Interface Circuits (SLIC). For short
loop applications, the voltage between the tip and ring
terminals varies to maintain a constant loop current. For long
loop applications, the voltage between the tip and ring
terminals are relatively constant and the loop current varies
in proportion to the load.
The tip and ring voltages for various loop resistances are
shown in Figure 13. The tip voltage remains relatively
constant as the ring voltage moves to limit the loop current
for short loops.
The loop current for various loop resistances are shown in
Figure 14. For short loops, the loop current is limited to the
programmed current limit, set by RILIM. For long loop
applications, the loop current varies in accordance with
Ohms law for the given tip to ring voltage and the loop
resistance.
.
The following discussion separates the SLIC’s operation into
its DC and AC paths, then follows up with additional circuit
and design information.
DC Feed Curve
The DC feed curve for the UniSLIC14 family is user
programmable. The user defines the on hook and off hook
overhead voltages (including the overhead voltage for off
hook pulse metering if applicable), the maximum and
minimum loop current limits, the switch hook detect
threshold and the battery voltage. From these requirements,
the DC feed curve is customized for optimum operation in
any given application. An Excel spread sheet to calculate the
external components can be downloaded off our web site
www.intersil.com/telecom/unislic14.xls.
FIGURE 13. TIP AND RING VOLTAGES vs LOOP RESISTANCE
TIP
AND
RING
VOLTA
GES
(V
)
LOOP RESISTANCE (
)
0
-5
-10
-15
-20
-25
-30
-35
-50
-40
-45
200
600 1000 1400 1800 2000
4K
10K
6K
8K
CONSTANT
LOOP CURRENT
REGION
VBH = -48V
RD = 41.2k
ROH = 38.3k
RDC_RAC = 19.6k
RILim = 33.2k
CONSTANT TIP TO RING
VOLTAGE REGION
-44.5V
-2.5V
TIP
RING
FIGURE 14. LOOP CURRENT vs LOOP RESISTANCE
LOOP
CURR
E
N
T
(mA)
0
LOOP RESISTANCE (
)
200
600
1K
1.4K 1.8K 2.2K 2.6K
3.8K
3.0K 3.4K
35
30
25
20
15
10
5
CONSTANT
LOOP CURRENT
REGION
VBH = -48V
RD = 41.2k
ROH = 38.3k
RDC_RAC = 19.6k
RILim = 33.2k
CONSTANT TIP TO RING
VOLTAGE REGION
HC55120, HC55121, HC55130, HC55140, HC55142, HC55143, HC55150
相關PDF資料 |
PDF描述 |
|---|---|
| HC55142IMZ | IC SLIC UNIVERSAL LP 28-PLCC |
| S9S08AW32E5MPUE | MCU 32K FLASH AUTO MONET 64-LQFP |
| S9S08AW32E5MFUE | MCU 32K FLASH AUTO MONET 64-QFP |
| MC9S08QE96CLK | IC MCU 8BIT 96K FLASH 80-LQFP |
| HC55140IMZ | IC SLIC UNIVERSAL LP 28-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HC55143 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power Universal SLIC Family |
| HC55143IM | 功能描述:IC SLIC UNIVERSAL LP 32-PLCC RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:UniSLIC14 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| HC5514X | 制造商:Harris Corporation 功能描述: |
| HC5514XB | 制造商:Harris Corporation 功能描述: |
| HC5514XEVAL1 | 功能描述:界面開發工具 UNISLIC14 FAMILY EVALUATION BRD RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。