- 您現在的位置：買賣IC網 > PDF目錄384360 > GT3200-JV (STANDARD MICROSYSTEMS CORP) USB2.0 PJY IC PDF資料下載
參數資料
| 型號： | GT3200-JV |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 網絡接口 |
| 英文描述： | USB2.0 PJY IC |
| 中文描述： | DATACOM, INTERFACE CIRCUIT, PQFP64 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, GREEN, TQFP-64 |
| 文件頁數： | 36/51頁 |
| 文件大?。?/td> | 1462K |
| 代理商： | GT3200-JV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
USB2.0 PHY IC
Revision 1.3 (10-05-04)
31
SMSC GT3200, SMSC USB3250
DATASHEET
1. If the device is suspended and it detects an SE0 state on the bus it may immediately enter the HS
handshake detection process.
2. If the device is in FS mode and an SE0 state is detected for more than 2.5μs. it may enter the HS
handshake detection process.
3. If the device is in HS mode and an SE0 state is detected for more than 3.0ms. it may enter the
HS handshake detection process. In HS mode, a device must first determine whether the SE0 state
is signaling a suspend or a reset condition. To do this the device reverts to FS mode by placing
XCVRSELECT and TERMSELECT into FS mode. The device must not wait more than 3.125ms
before the reversion to FS mode. After reverting to FS mode, no less than 100μs and no more
than 875μs later the SIE must check the LINESTATE signals. If a J state is detected the device
will enter a suspend state. If an SE0 state is detected, then the device will enter the HS Handshake
detection process.
In each case, the assertion of the SE0 state on the bus initiates the reset. The minimum reset interval
is 10ms. Depending on the previous mode that the bus was in, the delay between the initial assertion
of the SE0 state and entering the HS Handshake detection can be from 0 to 4ms.
This transceiver design pushes as much of the responsibility for timing events on to the SIE as
possible, and the SIE requires a stable CLKOUT signal to perform accurate timing. In case 2 and 3
above, CLKOUT has been running and is stable, however in case 1 the PHY is reset from a suspend
state, and the internal oscillator and clocks of the transceiver are assumed to be powered down. A
device has up to 6ms after the release of SUSPENDN to assert a minimum of a 1ms Chirp K.
8.8
HS Detection Handshake - FS Downstream Facing Port
Upon entering the HS Detection process (T0) XCVRSELECT and TERMSELECT are in FS mode. The
DP pull-up is asserted and the HS terminations are disabled. The SIE then sets OPMODE to Disable
Bit Stuffing and NRZI encoding, XCVRSELECT to HS mode, and begins the transmission of all 0's
data, which asserts a HS K (chirp) on the bus (T1). The device chirp must last at least 1.0ms, and
must end no later than 7.0ms after HS Reset T0. At time T1 the device begins listening for a chirp
sequence from the host port.
If the downstream facing port is not HS capable, then the HS K asserted by the device is ignored and
the alternating sequence of HS Chirp K's and J's is not generated. If no chirps are detected (T4) by
the device, it will enter FS mode by returning XCVRSELECT to FS mode.
相關PDF資料 |
PDF描述 |
|---|---|
| GTF701-HS3 | 2-Line EMI-Filter with ESD -Protection |
| GTF701-HS3-GS08 | 2-Line EMI-Filter with ESD -Protection |
| GTO1200-2R | Snubber Capacitors, Dry Self-healing |
| GTO2940-12RP | GTO Clamping Capacitors, Self-healing, Segmented |
| GTRFS571 | Mini size of Discrete semiconductor elements |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GT3-2024SCF | 制造商:Hirose 功能描述: |
| GT3-2024SCF(70) | 制造商:Hirose 功能描述: |
| GT-32090-A0-PBN-C000 | 制造商:Marvell 功能描述: |
| GT3-20DP-2.5DSA | 制造商:HRS 制造商全稱:HRS 功能描述:Antenna, Sensor, and Communications Trunk Line Connections |
| GT321 | 制造商:CORNELL DUBILIER ELECTRONICS 功能描述:Cap Ceramic 220pF 3000V SL 5% (20 X 6mm) Radial 9.5mm 85°C |
發布緊急采購，3分鐘左右您將得到回復。