參數資料
型號： GS8644Z36E-150I
廠商： Electronic Theatre Controls, Inc.
英文描述： Header; No. of Contacts:10; Pitch Spacing:0.079"; No. of Rows:2; Gender:Male; Series:1552; Body Material:Glass Filled Polyester; Connector Retention Style:Latch/Ejector; Contact Termination:Through Hole; Housing Style:Right-Angle RoHS Compliant: Yes
中文描述： 72Mb流水線和流量，通過同步唑的SRAM
文件頁數： 26/39頁
文件大?。?/td> 1174K
代理商： GS8644Z36E-150I
Product Preview
GS8644Z18(B/E)/GS8644Z36(B/E)/GS8644Z72(C)
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Rev: 1.03 11/2004
26/39
2003, GSI Technology
JTAG Port Registers
Overview
The various JTAG registers, refered to as Test Access Port orTAP Registers, are selected (one at a time) via the sequences of 1s
and 0s applied to TMS as TCK is strobed. Each of the TAP Registers is a serial shift register that captures serial input data on the
rising edge of TCK and pushes serial data out on the next falling edge of TCK. When a register is selected, it is placed between the
TDI and TDO pins.
Instruction Register
The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle, or
the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the
TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the
controller is placed in Test-Logic-Reset state.
Bypass Register
The Bypass Register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through
the RAM’s JTAG Port to another device in the scan chain with as little delay as possible.
Boundary Scan Register
The Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM’s input or I/O pins.
The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port’s TDO pin. The
Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the
device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan
Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in
Capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to Shift-DR state. SAMPLE-Z,
SAMPLE/PRELOAD and EXTEST instructions can be used to activate the Boundary Scan Register.
JTAG Pin Descriptions
Pin
Pin Name
I/O
Description
TCK
Test Clock
In
Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate
from the falling edge of TCK.
TMS
Test Mode Select
In
The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP
controller state machine. An undriven TMS input will produce the same result as a logic one input
level.
TDI
Test Data In
In
The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers
placed between TDI and TDO. The register placed between TDI and TDO is determined by the
state of the TAP Controller state machine and the instruction that is currently loaded in the TAP
Instruction Register (refer to the TAP Controller State Diagram). An undriven TDI pin will produce
the same result as a logic one input level.
TDO
Test Data Out
Out
Output that is active depending on the state of the TAP state machine. Output changes in
response to the falling edge of TCK. This is the output side of the serial registers placed between
TDI and TDO.
Note:
This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is
held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up.
相關PDF資料
PDF描述
GS8644Z36E-166 Header; No. of Contacts:10; Pitch Spacing:0.079"; No. of Rows:2; Gender:Male; Series:1552; Body Material:Glass Filled Polyester; Connector Retention Style:Latch/Ejector; Contact Termination:Through Hole; Housing Style:Right-Angle RoHS Compliant: Yes
GS8644Z36E-166I Header; No. of Contacts:10; Pitch Spacing:0.079"; No. of Rows:2; Gender:Male; Series:1552; Body Material:Glass Filled Polyester; Connector Retention Style:Latch/Ejector; Contact Termination:Through Hole; Housing Style:Right-Angle RoHS Compliant: Yes
GS88018AT-133 512K x 18, 256K x 32, 256K x 36 9Mb Sync Burst SRAMs
GS88018AT-133I 512K x 18, 256K x 32, 256K x 36 9Mb Sync Burst SRAMs
GS88018AT-150 512K x 18, 256K x 32, 256K x 36 9Mb Sync Burst SRAMs
相關代理商/技術參數
參數描述
GS8644Z36E-150IV 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Pipelined and Flow Through Synchronous NBT SRAM
GS8644Z36E-150V 制造商:GSI 制造商全稱:GSI Technology 功能描述:72Mb Pipelined and Flow Through Synchronous NBT SRAM
GS8644Z36E-166 制造商:未知廠家 制造商全稱:未知廠家 功能描述:72Mb Pipelined and Flow Through Synchronous NBT SRAM
GS8644Z36E-166I 制造商:GSI Technology 功能描述:SRAM SYNC QUAD 2.5V/3.3V 72MBIT 2MX36 7NS/3.5NS 165FBGA - Trays 制造商:GSI 功能描述:
GS8644Z36E-166IV 制造商:GSI Technology 功能描述:SRAM SYNC SGL 1.8V/2.5V 72MBIT 2MX36 7NS/2.9NS 165FPBGA - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*