- 您現在的位置：買賣IC網 > PDF目錄384345 > GS1560ACFE3 (Gennum Corporation) GS1560A/GS1561 HD-LINX-R II Dual-Rate Deserializer PDF資料下載
參數資料
| 型號： | GS1560ACFE3 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS1560A/GS1561 HD-LINX-R II Dual-Rate Deserializer |
| 中文描述： | GS1560A/GS1561的HD - LINX進程- R的第二雙率解串器 |
| 文件頁數： | 9/80頁 |
| 文件大?。?/td> | 842K |
| 代理商： | GS1560ACFE3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
GS1560A/GS1561 Data Sheet
27360 - 8
September 2005
9 of 80
11
SD/HD
Non
Synchronous
Input /
Output
CONTROL SIGNAL INPUT / STATUS SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
This pin will be an input set by the application layer in slave mode, and will
be an output set by the device in master mode.
Master Mode (MASTER/SLAVE = HIGH)
The SD/HD signal will be LOW whenever the received serial digital signal
is 1.485Gb/s or 1.485/1.001Gb/s.
The SD/HD signal will be HIGH whenever the received serial digital signal
is 270Mb/s.
Slave Mode (MASTER/SLAVE = LOW)
When set LOW, the device will be configured for the reception of
1.485Gb/s or 1.485/1.001Gb/s signals only and will not lock to any other
serial digital signal.
When set HIGH, the device will be configured for the reception of 270Mb/s
signals only and will not lock to any other serial digital signal.
NOTE: When in slave mode, reset the device after the SD/
HD
input has
been initially configured, and after each subsequent SD/HD data rate
change.
NOTE: This pin has an internal pull-up resistor of 100K.
12
20bit/10bit
Non
Synchronous
Input
CONTROL SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to select the output data bus width in SMPTE or Data-Through
modes. This signal is ignored in DVB-ASI mode.
When set HIGH, the parallel output will be 20-bit demultiplexed data.
When set LOW, the parallel outputs will be 10-bit multiplexed data.
13
IOPROC_EN/DIS
Non
Synchronous
Input
CONTROL SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to enable or disable I/O processing features.
When set HIGH, the following I/O processing features of the device are
enabled:
EDH CRC Error Correction (SD-only)
ANC Data Checksum Correction
Line-based CRC Error Correction (HD-only)
Line Number Error Correction (HD-only)
TRS Error Correction
Illegal Code Remapping
To enable a subset of these features, keep IOPROC_EN/DIS HIGH and
disable the individual feature(s) in the IOPROC_DISABLE register
accessible via the host interface.
When set LOW, the I/O processing features of the device are disabled,
regardless of whether the features are enabled in the IOPROC_DISABLE
register.
Table 1-1: Pin Descriptions (Continued)
Pin
Number
Name
Timing
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| GS1561-CF | GS1560A/GS1561 HD-LINX-R II Dual-Rate Deserializer |
| GS1561-CFE3 | GS1560A/GS1561 HD-LINX-R II Dual-Rate Deserializer |
| GS1574A | GS1574A HD-LINX-R II Adaptive Cable Equalizer |
| GS1574ACNE3 | GS1574A HD-LINX-R II Adaptive Cable Equalizer |
| GS1574 | GS1574 HD-LINX -TM II Adaptive Cable Equalizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS1561 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II Dual-Rate Deserializer |
| GS1561-CF | 制造商:Rochester Electronics LLC 功能描述: 制造商:Gennum Corporation 功能描述: |
| GS1561-CFE3 | 制造商:Semtech Corporation 功能描述:Receiver for HD/SD/ASI w/out loop thru |
| GS1561-CFT | 制造商:Rochester Electronics LLC 功能描述: 制造商:Gennum Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。