參數資料
型號: GL711FW
廠商: Electronic Theatre Controls, Inc.
英文描述: ATA/ATAPI to 1394 Native Bridge Two in One Solution
中文描述: ATA / ATAPI接口,以1394的積分橋一兩個解決方案
文件頁數: 6/17頁
文件大小: 287K
代理商: GL711FW
GL711FW
Revision: 1.3
-5-
Functional Overview
The GL711FW is designed to simplify the firmware issue of
μ
P (8052) and save hardware cost.
Upon the completion of a packet reception, the GL711FW will automatically respond
acknowledge code according to the destination offset and generate the corresponding interrupt
to inform the firmware to check if the received packet meets SBP-2 and 1394 protocol or not.
The data payload dedicated to SBP-2 protocol is moved to the specified registers so that
firmware can easily inquire and reply the data packet according to the received packet if
necessary. The
μ
P has to do is to set "1394 instruction register" properly and then the internal
SBP-2 engine will automatically collect all fields from SBP-2 registers to generate the data
packet. For the SCSI command that requested from initiator, firmware have to transfer these
commands to ATA/ATAPI commands, and write them to IDE device through I/O register to
access IDE interface. The embedded
μ
P and internal ROM can be disabled by negating ENUP#
and EA respectively for prototype development or other specific functions.
GL711FW architecture:
1.
Asyn Tx registers:
general asynchronous packet transmit registers, 4-quadlets for 1394
header and 8-quadlets for data payload. After getting all fields of packet ready, the
firmware can set “AsynTx” instruction to send the packet. Some packets for transmitting
packets like “Login Response”, “Query Login Response” and “Status Block” are prepared
by the registers whose maximum data payload is 8 quadlets.
2.
Asyn Rx registers:
general asynchronous packet receives registers, 4-quadlets for 1394
header and 8-quadlets for data payload. The received packet other than the SBP-2
associated read response packets, like "Config ROM Read Request" from the initiators, is
stored in the registers. However, all the SBP-2 read response packet received from the
initiators are always expected by the target and forwarded to the Auto Packet Distributor.
3.
1394 Control Registers:
control and interrupt registers for IEEE 1394 and SBP-2 protocol,
see the details in the section of 1394 control register.
4.
ADP State Machine:
Automatic data pipe control for SBP-2 data transfer and page table
fetch.
5.
Auto Packet Generator:
generate the read or write request packet header of those packets
with standard format like Config ROM read response packet, Management ORB read
request, Command ORB read request, Page Table read request, Block data read request
from or write request to initiator.
6.
Auto Packet Distributor:
The data payload of SBP-2 associated packet is stored at the
specified registers according to its destination offset, Tlabel or last request packet
command. The received data payload is classified by the GL711FW to 7 types:
相關PDF資料
PDF描述
GL816 USB 2.0 Flash Card Reader Controller
GL827 USB 2.0 Single Slot SD/MMC/MS/SM/xD-Picture Card Reader Controller
GL827-HHG USB 2.0 Single Slot SD/MMC/MS/SM/xD-Picture Card Reader Controller
GL827-MNG USB 2.0 Single Slot SD/MMC/MS/SM/xD-Picture Card Reader Controller
GL827-MWG USB 2.0 Single Slot SD/MMC/MS/SM/xD-Picture Card Reader Controller
相關代理商/技術參數
參數描述
GL7500 INT_1103348 功能描述:4G LTE 2G FALLBACK MODEM NAM 制造商:sierra wireless 系列:GL 零件狀態:在售 功能:調制解調器 調制或協議:LTE,HSPA+ 應用:通用 接口:UART,USB 靈敏度:- 功率 - 輸出:- 數據速率(最大值):- 特性:- 電壓 - 電源:4.75 V ~ 32 V 標準包裝:50
GL75019 制造商:Glenair Inc 功能描述:
GL7600 INT_1103343 功能描述:4G LTE 2G FALLBACK MODEM EMEA 制造商:sierra wireless 系列:GL 零件狀態:在售 功能:調制解調器 調制或協議:GSM,LTE 應用:通用 接口:UART,USB 靈敏度:- 功率 - 輸出:- 數據速率(最大值):- 特性:- 電壓 - 電源:4.75 V ~ 32 V 標準包裝:50
GL772 制造商:GTM 制造商全稱:GTM 功能描述:PNP EPITAXIAL PLANAR TRANSISTOR
GL7905 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:NEGATIVE VOLTAGE REGULATOR