參數資料
型號： GL600USB
廠商： Electronic Theatre Controls, Inc.
英文描述： USB MOUSE MICROCONTROLLER
中文描述： USB鼠標單片機
文件頁數： 12/38頁
文件大小： 352K
代理商： GL600USB
12
06/19/2000
GL600USB/GL600USB-A/GL600USB-B
Revision 1.3
17h
18h
19h
FFDAT0
FFDAT1
EP0RXST
Endpoint 0 FIFO port
Endpoint 1 FIFO port
Endpoint 0 receiving status register
Table 4-1 USB Function Register Summary
DEVCTL (Address 10h, Device control register)
R/W
[1]
TXSE0
TXSE0: Set and clear transmitting SE0 bit
1: Set transmitting SE0
0: Clear transmitting SE0
EP0STL: Endpoint 0 stall bit. This bit will be cleared automatically by hardware when SETUP packet is
received
1: Endpoint 0 will respond with a STALL to a valid transaction except SETUP
0: Endpoint 0 will not respond with a STALL to a valid transaction
EP1STL: Endpoint 1 stall bit
1: Endpoint 1 will respond with a STALL to a valid IN transaction
0: Endpoint 1 will not respond with a STALL to a valid IN transaction
WAKE: Wake-up bit
1: Set this bit to wake up host controller by placing USB bus into K state
0: Clear this bit to force USB bus leave K state
WKDIS: Wake-up disable bit. The WAKE bit has no effect if WKDIS bit is set to 1.
1: Disable remote wake-up capability
0: Enable remote wake-up capability
PWRDN: Power-down mode bit. Writing 1 to this bit will enter power-down mode
If USB suspend is detected, firmware can set this bit to enter power-down mode. In power-down
mode, crystal/resonator will stop. The PWRDN bit will be cleared automatically by hardware and
crystal/resonator will restart when the internal RC timer timeout (about 500ms). Firmware should
check buttons and photo position encoders of the mouse. If mouse status is not changed, Firmware
should set the PWRDN bit to enter power down mode again. Power consumption in suspend mode
depends on how much time the firmware checking mouse status changed. Hardware will also clear
PWRDN bit automatically when USB D+ or D- is toggled.
0: Normal mode, not power-down
Value on POR: “1 - 0 - 0 0 0 0”
[2]
Note 1: “R/W” means readable and writable bit. All reserved fields should not be changed by firmware.
Note 2: “-“ means unimplemented read as 0
EVTFLG (Address 12h, Event flag register)
R/W1C
[1]
RESUME
RESUME: Global resume bit
1: Global resume (USB D+/D- toggle) was detected
0: Global resume was not detected
SUSPD: Global suspend bit
1: Global suspend (USB idle more than 3ms) was detected
0: Global suspend was not detected
EP1TX: Endpoint 1 transmitting status bit
1: Data has been sent from endpoint 1
0: Data has not been sent from endpoint 1
EP0TX: Endpoint 0 transmitting status bit
1: Data has been sent from endpoint 0
0: Data has not been sent from endpoint 0
EP0RX: Endpoint 0 receiving status bit
R/W
EP0STL
R/W
EP1STL
R/W
WAKE
R/W
WKDIS
R/W
PWRDN
R/W1C
SUSPD
R/W1C
EP1TX
R/W1C
EP0TX
R/W1C
EP0RX
相關PDF資料
PDF描述
GL600USB-A USB MOUSE MICROCONTROLLER
GL600USB-B USB MOUSE MICROCONTROLLER
GL620USB GeneLink-Lite USB PC-to-PC File Transfer Controller
GL641USB USB ATA/ATAPI/ COMPACT FLASH CARD CONTROLLER
GL650USB USB 4 PORT HUB CONTROLLER
相關代理商/技術參數
參數描述
GL600USB-A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:USB MOUSE MICROCONTROLLER
GL600USB-B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:USB MOUSE MICROCONTROLLER
GL60209 制造商:Glenair Inc 功能描述:CONNECTOR - Bulk
GL602USB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:USB KEYBOARD MICROCONTROLLER
GL602USB-A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:USB KEYBOARD MICROCONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*