- 您現在的位置：買賣IC網 > PDF目錄370317 > GFU (意法半導體) Switch-Mode Driver for DC Motors(用于直流電機的開關模式驅動器) PDF資料下載
參數資料
| 型號： | GFU |
| 廠商： | 意法半導體 |
| 英文描述： | Switch-Mode Driver for DC Motors(用于直流電機的開關模式驅動器) |
| 中文描述： | 開關模式直流電動機的驅動程序（用于直流電機的開關模式驅動器） |
| 文件頁數： | 4/12頁 |
| 文件大小： | 161K |
| 代理商： | GFU |
4/12
The second input to each multipler consists of the
sign of the first input of the other multiplier before
differentiation, these are obtained using the compa-
rators C
s1
and C
s2
. The multiplier outputs, C
SA
and
C
SB
, are summed by A
3
to give the final output
signal TACHO. The peak-topeak ripple signal of the
TACHO can be found from the following expression:
V
ripple
p
p
=
π
4
(
√
2
1
)
V
thaco
DC
The max value of TACHO is:
V
tacho
max
=
π
4
√
2
V
thaco
DC
Using the coparators C
1
and C
2
another two signals
from V
AA
and V
AB
are derived - the logic signals STA
and STB.
This signals are used by the microprocessor to
determine the position by counting the pulses.
The L2910 internal reference voltage is also derived
from V
AA
and V
AB
:
V
ref
=
|
V
AA
|
+
|
V
AB
|
This reference is used by the D/A converter in the
L291 to compensate for variations in input levels,
temperature changes and ageing.
The "one pulse per rotation" opto encoder output
is connected to pin 12 of the L290 (FTF) where it is
squared to give the STF logic output for the micro-
processor.
The TACHO signal and V
ref
are sent to the L291 via
filter networks R
8
C
8
R
9
and R
6
C
7
R
7
respectively.
Pin 12 of this chip is the main summing point of the
system where TACHO and the D/A converter output
are compared.
The input to D/A converter consists of 5 bit word
plus a sign bit supplied by the microprocessor. The
sign bit represets the direction of motor rotation.
The (analogue) output of the D/A conveter -
DAC/OUT - is compared with the TACHO signal and
the risulting error signal is amplified by the error
amplifier, and subsequently appears on pin 1.
The ERRV sognal (from pin 1 , L291) is fed to pin
6 of the final chip, the L292 H-bridge motor-driver.
This input signals is bidirectional so it must be
converted to a positive signal bacause the L292
uses a single supply voltage. This is accomplished
by the first stage - the level shifter, which uses an
internally generated 8 V reference.
This same reference voltage supplies the triangle
wave oscillator whose frequency is fixed by the
external RC network (R
20
, C
17
- pins 11 and 10)
where:
1 f
osc
=
1
2RC
(
with
R
≥
8.2
K
)
The oscillator determines the switching frequency
of the output stage and should be in the range 1 to
30 KHz.
Motor current is regulated by an internal loop in the
L292 which is performed by the resistors R
18
, R
19
and the differential current sense amplifier, the out-
put of which is filtered by an external RC network
and fed back to the error amplifier.
The choise of the external components in these RC
network (pins 5, 7, 9) is determined by the motor
type and the bandwidth requirements. The values
shown in the diagram are for a 5
, 5 MH motor.
(See L292 Transfer Function Calculation in Appli-
cation Information).
The error signal obtained by the addition of the input
and the current feedback signals (pin 7) is used to
pulse width modulate the oscillator signal by means
of the comparator. The pulse width modulated sig-
nal controls the duty cycle of the Hbridge to give an
output current corresponding to the L292 input
signal.
The interval between one side of the bridge switch-
ing off and the other switching on,
τ
, is programmed
by C
17
in conjuction with an internal resistor R
τ
.
This can be foud from:
τ
=
R
τ
C
pin
10.
(
C
17
in
the
diagram
)
Since R
τ
is approximately 1.5 K
and the recom-
mended
τ
to avoid simultaneous conduction is 2.5
μ
s C
pin 10
should be around 1.5 nF.
The current sense resistors R
18
and R
19
should be
high precision types (maximum tolerance
±
2 %)
and the recommended value is given by:
R
max
I
o
max
≤
0.44 V
It is possible to synchronize two L292 ’s, if desired,
using the network shown in fig. 2.
Finally, two enable inputs are provited on the L292
(pins 12 and 13-active low and high respectively).
Thus the output stage may be inhibited by taking
pin 12 high or by taking pin 13 low. The output will
also be inhibited if the supply voltage falls below 18
V.
L292
相關PDF資料 |
PDF描述 |
|---|---|
| GFW | Push-Pull Four Channel Drivers(推挽式四通道驅動器) |
| GFZ1Q | 1.0 Amp Glass Passivated Sintered Rectifiers |
| GFZ1A | 1.0 Amp Glass Passivated Sintered Rectifiers |
| GFZ1B | 1.0 Amp Glass Passivated Sintered Rectifiers |
| GFZ1D | 1.0 Amp Glass Passivated Sintered Rectifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GFU1620U7 | 制造商:Schneider Electric 功能描述:RELAY IMPULSE 2N/O 制造商:Schneider Electric 功能描述:RELAY, IMPULSE, 2N/O |
| GFU50N03\45A | 功能描述:MOSFET N-Channel 30V 65A RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| GF-USB-8M-32 | 制造商:Mencom 功能描述: |
| GFWB3 | 制造商:Soshin Electric Co Ltd 功能描述:BAND PASS FILTER |
| GFWQ1010 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Ceramic Capacitor Stacks |
發布緊急采購，3分鐘左右您將得到回復。