- 您現在的位置：買賣IC網 > PDF目錄370298 > G9611 LDO with reset. Io=300mA.|LDO regulator PDF資料下載
參數資料
| 型號： | G9611 |
| 英文描述： | LDO with reset. Io=300mA.|LDO regulator |
| 中文描述： | 穩壓器的復位。木衛一\u003d 300mA的。| LDO穩壓器 |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 509K |
| 代理商： | G9611 |
Ver: 1.2
Feb 13, 2003
TEL: 886-3-5788833
http://www.gmt.com.tw
5
G9611
Global Mixed-mode Technology Inc.
Pin Description
PIN NO.
1, 6
2
PIN NAME
N.C
PIN FUNCTION
No Connection.
RESET
RESET
Open-Drain Output remains low while V
IN
is below the reset threshold,
and for delay time set by C
D
after V
IN
rises above the reset threshold.
SHDN
= High to enable regulator output.
3
SHDN
SHDN
= Low to shutdown regulator output.
4
5
7
8
V
IN
V
OUT
GND
C
D
Regulator Input. Supply voltage can range from 2.5V to 6V.
Regulator Output. Sources up to 300mA.
Ground
External Programmable time delay is set by the capacitor connect to C
D
pin.
Figure 1. Functional Diagram
Detailed Description
The G9611 are low-dropout, low-quiescent current
linear regulators with reset function The regulator in
G9611 supply 3.4V, 3.3V or 2.5V output for load cur-
rents up to 300mA. The reset function detect V
IN.
As
illustrated in Figure 1, they consist of a 1.24V refer-
ence, error amplifier, MOSFET driver, P-channel pass
transistor, and internal feedback voltage divider, reset
threshold comparator and time delay generator.
The 1.24V bandgap reference is connected to the er-
ror amplifier’s inverting input. The error amplifier com-
pares this reference with the feedback voltage and
amplifies the difference. The MOSFET driver reads the
error signal and applies the appropriate drive to the
P-channel pass transistor. If the feedback voltage is
lower than the reference, the pass transistor gate is
pulled lower, allowing more current to pass and in-
creasing the output voltage. If the feedback voltage is
too high, the pass transistor gate is pulled up, allowing
less current to pass to the output.
Additional blocks of linear regulator include a foldback
current limiter, thermal sensor, and shutdown logic.
The G9611 also offer reset function to detect the level
of V
IN
. They assert a reset signal whenever V
IN
supply
voltage declines below a preset threshold (V
TH
), keep-
ing it asserted for time delay set by capacitor con-
nected to C
D
pin, after V
IN
has resen above the high
reset threshold (V
TH
+ V
HYS
). The
RESET
is an active
low, open-drain output.
Internal P-Channel Pass Transistor
The G9611 feature a 300mA P-channel MOSFET
pass transistor. This provides several advantages over
similar designs using PNP pass transistors, including
longer battery life. The P-channel MOSFET requires
no base drive, which reduces quiescent current con-
siderably. PNP based regulators waste considerable
amounts of current in dropout when the pass transistor
saturates. They also use high base-drive currents un-
der large loads. The G9611 do not suffer from these
problems and consume only 320μA of quiescent cur-
rent.
V
OUT
LOGIC
1.24V
REFERENCE
－
＋
CURRENT LIMIT
R1
R2
PROTECTION
P
－
＋
SHDN
C
D
R
D
V
IN
GND
RESET
SHUTDOWN
MOSFET DRIVER
WITH FOLDBACK
THERMAL
相關PDF資料 |
PDF描述 |
|---|---|
| G9612 | LDO with reset. Io=500mA.|LDO regulator |
| G9S-2001DC24 | |
| G9S-2002DC24 | |
| G9S-301AC120 | |
| G9S-301AC24 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| G961-15ADJTEU | 制造商:GMT 制造商全稱:Global Mixed-mode Technology Inc 功能描述:1A Low Dropout Regulator with Enable |
| G961-15ADJTEUF | 制造商:GMT 制造商全稱:Global Mixed-mode Technology Inc 功能描述:1A Low Dropout Regulator with Enable |
| G961-18ADJTEU | 制造商:GMT 制造商全稱:Global Mixed-mode Technology Inc 功能描述:1A Low Dropout Regulator with Enable |
| G961-18ADJTEUF | 制造商:GMT 制造商全稱:Global Mixed-mode Technology Inc 功能描述:1A Low Dropout Regulator with Enable |
| G9611AP1T | 制造商:GMT 制造商全稱:Global Mixed-mode Technology Inc 功能描述:Low-Dropout, 300mA Linear Regulator with Reset |
發布緊急采購，3分鐘左右您將得到回復。